-
Specify the time-dependent pressure boundary condition in TOUGH+HYDRATE
Hi, everyone Can I set a time-dependent pressure boundary condition in the TOUGH+HYDRATE? I wonder if it is possible to decrease the pressure of the production well over time. Thanks!
-
Gas production units in TOUGH+ is it m3/d or Sm3/d in Hydrate_Status : T+H v 1.5
I am trying to figure out whether T+H v 1.5 reports Sm3/d in Hydrate status file or simply m3/d. If it is m3/d then how do i get the necessary Thermodynamic variables to change it to Sm3/d.…
-
TOUGH+HYDRATES convergence issue in phase change
I want to calculate the depth interval at which gas hydrates forms, given P and T initial conditions, fixed on top. The idea is to run the model until it reaches the equilibrium,…
-
without the addition of inhibitors
Simulating the process of hydrate formation, without the addition of inhibitors, why is there no hydrate formation in some cells
-
pressure remains constant during the formation of hydrate
I am using T+H to simulate the formation of hydrate. May I ask how to ensure that the pressure remains constant during the formation of hydrate by using the constant pressure method
-
Well_Time_Series or Interface_Time_Seres.....What are these outputs....where to find description
Hello Toughers I ran simulation and i am having a hard time understanding the differences between the different headers listed in the interface output file which list production form the well…
-
GENER block injection fluid
Hello, There is an option for injection component on the TOUGH+HYDRATE GENER data block defined by COM1, COM2, COM3, etc. However it doesn't specify how we can inject a particular fluid into an…
-
The order of ELEME and CONNE will influence computation results
I used to think that ELEME and CONNE can be arranged in arbitrary order as long as the blocks provide same information, but recently I found changing the order of ELEME and CONNE can significantly…
-
Inhibitor parameters in T+H
Browsing through the sample files I encountered the following two lines that sets up the inhibitor in the HYDRATE Section. In the manual, the following parameters are set for the variables…
-
Geo-gridding for TOUGH+
Hi, besides flat cartesian and axis-symmetric radial grids, is it possible to use in TOUGH+ a grid with tilted cells that honor geological dip like the added picture?
-
Compare [cumulative CH4(m3) ] from Well_Time_Series vs Hydrate_Info
Hello everyone I have a very simple problem Tough+Hydrate (v1.5) : I m trying to compare Methane production from the two sources (i) released from HYDRATE DISSOCIATION (ii) Total Production at the…
-
How to handle convergence
I am using a simple 2D grid to simulate the growth of hydrates after some gas injection occurs in the system. Ideally I would like to shut down the source (injector) and let the system evolve with…
-
Pre/post processing tools for TOUGH+ Hydrate
Hi, I am starting to use this tool and wondered if PyTOUGH could be used for this? I am familiar to Python and would be nice to know if there exists scripts fro pre and postprocessing in Python.…
-
Injecting Methane in TOUGH+RealGasBrine model, but none appears in output
Hello, I am trying to run a simple 1-D model in which I inject gas phase methane into an initially water-saturated column of rocks. I have been able to model this system using TOUGH2-EOS7C and…
-
TOUGH+ 3D model fails to run after uniformly scaling down the mesh
Dear friends, I am currently conducting TOUGH-FLAC3D coupling calculations. I constructed a 100 × 50 × 50 model using FLAC3D, with 15, 7, and 7 grids in three directions respectively.…
-
Tough+Hydrate Model Initialization to Steady state : Pressure gradient appears but Temperature gradient disappears
Hello Everyone. I am trying to run the model to steady state. I have a 190 x 1000 model. I fixed the top boundary to 6.5C and 104bar by making the cells inactive I set simulation end time to (10,…
-
Importing of pore-pressure obtained from T+H simulation to FLAC-3D
Hi all, Can someone help me with the python script for importing pore-pressure obtained from T+H simulation to FLAC-3D? Thank you in advance.
-
HOW DOES THE ELEME BLOCK WORK? (NOVICE ALERT!!)
Hi guys, I am a novice in using T+H. Could someone explain to me the values in the ELEME block input file for the Test_1T Problem in the Manual? Also, in the CONNE block,…
-
Where to find input files for Tough+Hydrate v1.2 version, other than the ones in the manual?
Hi everyone, Does anyone know of a website where I could find input files of 1.2 version in order to compare to the examples in the manual? Or better still, can anyone post me their input files?…
-
How to set SAVE_Frequency =500 in Input File-T+H Simulation
Hello Lately, i have been tryin to set the SAVE_Frequency parameter to set the writing of SAVE file recurringly, i.e., to update in order to prevent loss of data.…
-
Ice in porous media T+H
Is it possible to model gas hydrate simulations in ice-bearing layers? Although there are different ice phases in TOUGH+HYDRATE, when we add ice into the system we got convergence failure problem.
-
No error, nothing... Why this file refuses to Run? Tried everything, but it just wont run.
I am modeling a R-Z system(100-X, 190-Z). There are just three layers, TOPSD, BOTSD, and HYDRL, apart from thin top and bottom cell. Everything is setup correctly.…
-
Large Size of Plot_Data_Elem file
I am getting very large Plot_Data_Eleme output file (20 GB). Is it normal? Is it possible to get this file only for certain time interval instead of all time steps?
-
IF WE CAN VISUALIZE THE VECTOR OF GAS AND WATER ON TOUGH+HYDRATE
If we can export Darcy flux vector of gas and water without change the source code of TOUGH+HYDRATE like that: