-
Hi everyone, i have been able to run the test examples and plotted the outputs. However, i have some
questions. i noticed these dimensions "below" in the input files, i would like to know how these dimensions were generated and is there any means to virtual the data. I will like to generate my own data. thanks
ELEME
A00 1 10.1000E+000.4000E+00 0.5100E-01-.5000E+00-.5000E+00
A00 2 10.1000E+000.4000E+00 0.1510E+00-.5000E+00-.5000E+00
A00 3 10.1000E+000.4000E+00 0.2510E+00-.5000E+00-.5000E+00
A00 4 10.1000E+000.4000E+00 0.3510E+00-.5000E+00-.5000E+00
A00 5 10.1000E+000.4000E+00 0.4510E+00-.5000E+00-.5000E+00
A00 6 10.1000E+000.4000E+00 0.5510E+00-.5000E+00-.5000E+00
A00 7 10.1000E+000.4000E+00 0.6510E+00-.5000E+00-.5000E+00
A00 8 10.1000E+000.4000E+00 0.7510E+00-.5000E+00-.5000E+00
A00 9 10.1000E+000.4000E+00 0.8510E+00-.5000E+00-.5000E+00
A0010 10.1000E+000.4000E+00 0.9510E+00-.5000E+00-.5000E+00
ina I
A00 0 10.1000E-020.4000E-02 0.5000E-03-.5000E+00-.5000E+00 I
CONNE
A00 0A00 1 10.5000E-030.5000E-010.1000E+01
A00 1A00 2 10.5000E-010.5000E-010.1000E+01
A00 2A00 3 10.5000E-010.5000E-010.1000E+01
A00 3A00 4 10.5000E-010.5000E-010.1000E+01
A00 4A00 5 10.5000E-010.5000E-010.1000E+01
A00 5A00 6 10.5000E-010.5000E-010.1000E+01
A00 6A00 7 10.5000E-010.5000E-010.1000E+01
A00 7A00 8 10.5000E-010.5000E-010.1000E+01
A00 8A00 9 10.5000E-010.5000E-010.1000E+01
A00 9A0010 10.5000E-010.5000E-010.1000E+01
A0010A0011 10.5000E-010.5000E-030.1000E+01
-
paul Do you have the meshmaker executable within your files? ELEME and CONNE sections are generated easily by Meshmaker.
-
-
Hi Paul,
I have started working on numerical modeling of gas hydrate in porous media. I am new to tough+hydrate. I have installed the same on my laptop. I am confused about how to start with it. I am not able to find out the place where to write the code. I have come across the black screen which on entering ask for the title but on writing the title and pressing enter, the screen crashes. It's just totally new to me, I have started to follow the tough+ hydrate manual, it says all about the what the code does and what are the input parameters but where to put that codes, I am still not able to figure it out.
Any sort of suggestion will be appreciated.
Thanks
-
I am able to figure out the simulator.
-
Alok Prasad not*
-
Alok Prasad You need to run the program in terminal or cmd. Open a terminal and go to the location where the executable file is place. Type its name followed by input file name and the output file name. For example:
t+h.exe <case_1.in> case_1.out
-
