-
TOUGH-HYDRATE - Problems with the maximum mass fraction of methane in aqueous phase
I'm trying to equilibrate a sloping system, containing a AqH phase and a Aqu phase. If methane mass fractions of methane in water are not maximum, hydrate phase dissolves.…
-
Tough+Realgasbrine
Hi there, I'm planning to attend the short course of Tough+Realgasbrine in September, is it a new module going to be released? Do you have any idea when will it be available? Thanks.
-
GENER block injection fluid
Hello, There is an option for injection component on the TOUGH+HYDRATE GENER data block defined by COM1, COM2, COM3, etc. However it doesn't specify how we can inject a particular fluid into an…
-
DIFFUSION Block
Hi, I am using TOUGH+Hydrate and I'm fairly new to it and learning as I go. I am using injection of water into a gas bearing reservoir. I wanted to include the diffusion block and tried the example…
-
Porosity reduction by hydrate/ice deposit
Hi, I have a question regarding the porosity reduction of a rock after hydrate/ice formation. I see that there is the compressibility and expansivity option on the ROCKS data block which determines…
-
Pre/post processing tools for TOUGH+ Hydrate
Hi, I am starting to use this tool and wondered if PyTOUGH could be used for this? I am familiar to Python and would be nice to know if there exists scripts fro pre and postprocessing in Python.…
-
Injecting Methane in TOUGH+RealGasBrine model, but none appears in output
Hello, I am trying to run a simple 1-D model in which I inject gas phase methane into an initially water-saturated column of rocks. I have been able to model this system using TOUGH2-EOS7C and…
-
how to define MOP
Hi all, I am a very fresh user and have some difficulties specifying MOP . TOUGH+ manual contains few examples of input files. I have read those and found myslef completely confused about which part…
-
Compiling/Executing TOUGH+RealGasBrine - Also, Hysteresis?
Hello, I would greatly appreciate some help getting TOUGH+RealGasBrine running on my PC. Below is a summary of the things I have tried so far without success:…
-
TOUGH+RealGasBrine for CO2 injection
Hi, I am working on CO2 injection in depleted Oil and Gas reservoirs for enhanced oil recovery and sequestration. I am planning to buy TOUGH+RealGasBrine for this purpose,…
-
How to set a production well with constant pressure
Hi everyone, How to set a horizontal production well with a fixed pressure in tough + hydrate? When setting source / sink in Gener, SS_ Type can only set a constant flow rate.…
-
How to handle convergence
I am using a simple 2D grid to simulate the growth of hydrates after some gas injection occurs in the system. Ideally I would like to shut down the source (injector) and let the system evolve with…
-
TOUGH+HYDRATE pre/post scripts
If there is any active user on T+H, is anyone interested in discussing pre and post processing options. After struggling for some time, I have managed to put some scripts in python to process both…
-
Gridblocks to represent sink and source
Hello all. I want to assign two vertical wells (137 layers) at the opposite end of my I dimension. I am stuck getting error messages trying to use GENER block’s NAD and NADS.…
-
Geo-gridding for TOUGH+
Hi, besides flat cartesian and axis-symmetric radial grids, is it possible to use in TOUGH+ a grid with tilted cells that honor geological dip like the added picture?
-
Tough+Hydrate (Data oscillation)
I encountered a problem in the calculation process and want to ask for help. When processing the calculation results, it is found that the gas production rate will fluctuate sharply at the initial…
-
About TOUGH+HYDRATE error
Hello, I have a question about TOUGH+HYDRATE(T+H). I want to run cartesian model (gird : 57x57x61(total about 200000). But T+H doesn't operate, and I get the following error message on the terminal:…
-
The program stops unexpectedly
My file works, but it stops suddenly after a period of time. I have tried many methods, changing the grid, changing the parameter settings, changing the initial conditions,…
-
Tough+Hydrate Model Initialization to Steady state : Pressure gradient appears but Temperature gradient disappears
Hello Everyone. I am trying to run the model to steady state. I have a 190 x 1000 model. I fixed the top boundary to 6.5C and 104bar by making the cells inactive I set simulation end time to (10,…
-
Assigning source/sink in GENER block without element name/ using meshmaker
Hello dear, A using cartesian grid of 200 x 340 for x and y dimension. Am not sure how to assign the element block data and the connections. I have the Meshmaker software which i fill in all the…
-
About the max computable number of elements.
I have the academic version of TOUGH+HYDRATE. I can only compute less than 10000 elements in windows10, and no more than 30000 elements. I want to know how can I compute more than that.…
-
Unexpected gas phase evolving
In a simulation case where no gas is defined nowhere in the initial conditions (Aqu with X_m_A=0) I am getting some values of gas at during the simulation.…
-
IF WE CAN VISUALIZE THE VECTOR OF GAS AND WATER ON TOUGH+HYDRATE
If we can export Darcy flux vector of gas and water without change the source code of TOUGH+HYDRATE like that: