TOUGH2-MP (no longer supported by LBNL) Category

TOUGH2-MP Compilation

I am a beginner trying to compile TOUGH2-MP. The manual mentions that I need to download AZTEC, but the official website for the package is no longer accessible.…

Tough2-MP post-processing and visualization

Hi everybody, can anyone, please, advise on software to extract and visualize results from TOUGH2-MP with ECO2N? I realise that EXT is not an option to extract results to tecplot,…

Subroutine NSIN

Hi everyone, I am running ECO2N in Tough2-mp, to simulate CO2 injection in a 3D model. Initialization of the model goes without problems, and the output is used as initial conditions for the CO2…

An error of test problem # 7: CO2 layered formation.

Dear all TOUGH2-MP users Hi. I'm Sungho Lee. Recently, I have been faced a problem about TOUGH2-MP. I installed TOUGH2-MP on my PC cluster(mater + 3 compute nodes).…

"ERRONEOUS DATA INITIALIZATION" on IBM-AIX cluster

I encountered a problem with "ERRONEOUS DATA INITIALIZATION" , when I tried to run serval tests using TOUGH2-MP on IBM-AIX cluster. These tests had been successfully tested using the usual Tough2.…

An encoding issue when TOUGH2-MP reads INFILE?

Hi, When I tried to run an example problem using TOUGH2-MP on an IBM-AIX supercomputer, I encountered an initialization problem that the executor terminated perhaps due to errors of reading the…

Need Help Choosing EOS Module

Hi everybody, I'm pretty new to TOUGH2 MP. I'm hoping somebody can help me, which EOS module should I use? To modeling natural gas production and reservoir compaction I use FLAC3D with a 3D…

TMVOC-MP is compiled but doesn't work

Hi Guys, After years of using TMVOC, we have recently bought TMVOC-MP. Unfortunately we have not yet had a pleasant experience and need some help. I tried to compile the code (with a headache…

Non isothermal simulations using ECO2N module

I am trying to run some simulations using TOUGH2-MP and compare the results with TOUGH2. The simulation runs successfully by TOUGH2 but when I tried to run it with TOUGh2-MP,…

TOUGH2-MP

Hello everybody, so I've successfully compiled TOUGH2-MP and decided to test it in the r1dv example files. I always get a segmentation fault error. Specifically I get the following message: [terra:…

Error message help

Hi Everyone, I am not sure I ask this question in the right forum. I am testing the Tough3 EOS1 with Minc. The cell number is about 0.4 million including the MINC element.…

TOUGH2-MP compilation error

Hello everybody, My research centre has a version of TOUGH2-MP and we are trying to install it with ECO2N eos in the cluster: Cluster: Rocks Cluster Operating System: Cent OS -> (2.6.32-220.13.1.el6.…

Tough2-MP TMVOC module

Hi, has anyone run TMVOC module with Tough2-MP successfully? Our current project has big area and needs fine mesh in pay zone, plus the MINC natural fractures,…

TOUGH2-MP EWASG: how to double check my installation

Hello, After some struggles, I managed to compile TOUGH2.01-MP with EWASG EOS on a cray machine (TITAN, OLCF, Oak Ridge TN). My compilation passed the test, but I'm not sure that it runs properly.…

How to make TOUGH2-MP v2.01

Hi, everyone. I have TOUGH2-MP v2.01 source code, and try to make execution file with below step. 1, "make configure" at tough2.01-mp. (modified Makefile: CC=icc, FC=ifort) 2, "make" at tough2.…

TOUGH2-MP and Tecplot

Hi everybody, I'm a new to TOUGH2-MP and therefore I don't know how I get my files into Tecplot. Is there any alternative like the EXT Software to extract and sort the data from the T2MP output data…

Gravity equilibrium for case "*r1dv* -- CO2 Discharge Along a Fault Zone" using ECO2N and TOUGH2-MP.

Hi! I have some comments/questions regarding the gravity equilibrium for test case *r1dv* ,section 5.3.1 in the ECO2N user manual page, 39. Using the ECO2N module and TOUGH2-MP,…

RTSOL keyword. Problem 4 (*rtp7*) - CO2 Injection using ECO2N for TOUGH2-MP

Hi! I am using TOUGH2-MP with the ECO2N module. In the install directory "eco2n/rtp7", I find the INFILE for the test case " Problem 4 (*rtp7*) - CO2 Injection into a 2-D Layered Brine Formation".…

Problem 4 (*rtp7*) - CO2 Injection into a 2-D Layered Brine Formation. SOLVR Block: HAVE READ UNKNOWN BLOCK LABEL "SOLVR"

Hi, I get the following message in OUTPUT file: HAVE READ UNKNOWN BLOCK LABEL "SOLVR" --- IGNORE THIS, AND CONTINUE READING INPUT DATA when running "Problem 4 (*rtp7*) - CO2 Injection into a 2-D…

Runtime error with TOUGH2-MP (Allocatable variable BCELEM)

Hello everyone, I'm new to TOUGH2-MP although we have the TOUGH2-code for some time now. We received the TOUGH2-MP code just some weeks ago. However I tried to compile it in on our cluster under…

Problem 4 (*rtp7*) - CO2 Injection into a 2-D Layered Brine Formation. What is the purpose of additional items in FOFT keyword?

Looking at "Problem 4 (*rtp7*) - CO2 Injection into a 2-D Layered Brine Formation" for the ECO2N module: The provided input file (INFILE) has the following FOFT section:…

Who use MOP(14) is one?

When I prepare INFILE, I can choose mop(x). For MOP(14), If I choose mop(14) is one, the length of element, connection incon, gener are 8 characters. If i choose mop(14) is zero,…

Jacobian in TOUGH2-MP

Hi, Is it possible to extract Jacobian matrix from TOUGH2-MP at each iteration step? Is it stored as sparse form? It wound be great if there is a way I can call the Jacobian subroutine to compute the…

Hello :)

Hi! My name is Sungho Lee. I'm really beginner of TOUGH2-mp Finally, I set up TOUGH2-mp on my lab's cluster. It is working well, I think. I don't have any knowleged , so I'm gonna study now and on.…