-
Simulation stops automatically at (9999,9)
Greetings, I have developed a field scale stacked reservoir model to simulate the flow and transport of sc-CO2 in the subsurface. In my model, the domain is 1 km in lateral extent and vertically it…
-
How to find a grid index
Hi, I am having trouble finding a grid index. I used FOFT to show temperature changes over time. However, I could not find the specific grid index I wanted to show the results for.…
-
Restart problem with T2Well
Hi, I assume T2Well has the same set up for "restart" as Tough2 or Tough3. I have summarized the sequence of my primary and secondary runs below to ask for advise.…
-
T2Well-ECO2M case not running
Hello T2Well user community and superusers of Tough-ECO2xxx, Would be great if you are interested to look into this case and see the possible source(s) of error.…
-
Heterogeneous field simulation
I was simulating water injection into oil reservoir with a heterogeneous permeability/porosity field using TOUGH3-EOS8. The heterogeneous permeability/porosity fields were realized by modifying the…
-
Error in installation
Can somebody help in rectifying the error encountered as shown in attached figure. Thank you in advance
-
PETSC configure command failed-when compile TOUGH3
I got the "PETSC configure command failed" error at compiling TOUGH3. I need some help. Thanks. cd /Users/wuhao/TOUGH3/TOUGH3v1.0/TOUGH3-Code/esd-tough3/build/tpl-build/tpls/petsc/petsc-3.7.…
-
GENER BLOCK : water pumping EOS7r two phase problem
Hello everyone, I want to pump water from a certain elements using EOS7R. I'm confused between using: 1. "COM1" as a type and a negative value of the rate (< 0) to mean that I extract water from this…
-
Is there a way to specify the component being produced from a source well?
My producing well is producing fluid through the ESP and venting gas through the casing annulus. Both flows are controlled independently. I am trying to history match the test and would like to…
-
EOS5 but Helium in stead of Hydrogen
Hello, I am trying to simulate a year long helium injection with varying rates using EOS5. I'm wondering if I would need to change something in the source code for this to run correctly,…
-
Mass balance of ECO2N
I was simulating constant CO2 injection into a 2D aquifer (salt not considered). For such 2-phase 2-component system, there should be 2 mass balance equations for CO2 and H2O, respectively,…
-
TOUGH3 vs TOUGH2-MP Printout of Mass fractions in single phase
Our understanding is that adding all component mass fractions of a phase add up to one. In TOUGH3 (or at least using eos3), it would appear that this is not the case.…
-
Two phase flow (Diffusion vs advection) with mesh sizes
Dear all, dear Finsterle, I have a question regarding the mesh size and its impact on diffusion in two-phase flow. I'm curious to know if the mesh size affects the diffusion from element0 to element1.…
-
Simple model test with ECO2N
I was testing the ECO2N module compiled by myself (Linux version). I built a simple model with 2 grids. I set pressure difference of 2MPa and gas saturation difference of 0.…
-
Hysteresis and non-wetting phase entrapment saturation
Hello everyone, First of all, thank you all for your help. I have a question related to gas permeability. In a wetting process where \( k_g(1 - S_{\delta_{gr}}) = k_g(S_{l^*}) = 0 \),…
-
cannot find -laztec
Hi folks, I am doing a clean TOUGH3 installation on a Linux system and want to use the PETSc solver. I have no interest in using the AZTEC solvers. But it seems I cannot finish building TOUGH3…
-
T2WELL deals with time scale inconsistencies
Hello, everyone. I would like to ask how T2WELL deals with the problem of inconsistency of wellbore and reservoir models in time scale?
-
T2WELL and TOGA coupling
Hello, everyone. Recently our group would like to do about CO2 injection into reservoir for CO2 flooding and sequestration based on wellbore-reservoir coupling model.…
-
Does TMVOCBio in TOUGH3 have any option for 3-phase hysteresis
Hi all, What I recall is that TMVOC did not have Hysteresis options for three-phase capillary pressure and relative permeabilities (see the link). Seems it is still the case in TMVOCbio (in TOUGH3).…
-
EOS7MG-A new TOUGH3 module for multiple gas mixture simulation
Recently, we have developed a new TOUGH3 EOS modules named ESO7MG. It is designed for modeling water, brine, and multiple gas species and their mixtures including hydrogen in subsurface multiphase…
-
how to debug Tough3 in vscode
Hi all, When configuring, I changed the -- build type to debug, which can generate an executable file called tough3-eco2n in the tough3-install folder. Then,…
-
Metis and parallel computing in Tough
Hi All, I found many descriptions about Metis in the User's guide of Tough2-MP. However, there is little description of Metis in Tough3. So, is Metis used in Tough3 for parallel computing? Moreover,…
-
MESHMAKER CORNERS
Good Morning All, I believe that a version of MESHMAKER (Meshmaker 2?) exists that writes a CORNERS attribute defining the nodes of an unstructured grid.…
-
How to visualize TOUGH MESH file in pyvista?
Hello TOUGH3 Forum, I got the above files, and want to visualize it with some python packages, e.g., pyvista or pytecplot. Now I can only read "MESH" file with the following code through toughio:…
