TOUGH Website

How to enable Javascript

TOUGH3

All topics

Efficient time stepping with great variability in pumping/shutin period durations
Dear colleagues, I am history matching a pumping test that consists of two 3day flow periods each followed by a 10d shutin periods. The flow rates were not constant during the pumping periods and…
- Yannick Champollion
- Yannick_Champollion
- 3 days ago
- 1 reply
- 8
- Alfredo Battistelli3 days ago
- TOUGH3
At KCYC=1, EXCEED GENERATION TIME TABLE AT ELEMENT #####
I was hoping someone would be able to help me troubleshoot this issue. I'm running EOS7C in TOUGH3. This is my OUTPUT file explanation of the error. CYCIT .......... KC = 1 KCYC = 1 DELT = 0.…
- Erik W
- Erik_W
- 7 days ago
- 5 replies
- 10
- Yingqi Zhangmoderator4 days ago
- TOUGH3
EOS7c and NCG injection
Dear all, I am using EOS7c module, to model the injection of a NCG (either CO2 or N2) in a depleted CH4 reservoir. As soon as the mass fraction of the non-condensible gas X_NCG_G approaches 1 (i.e.…
- lurpi
- lurpi.1
- 1 mth ago
- 3 replies
- 29
- kenny1 mth ago
- TOUGH3
AZ_calc_blk_diag_inv: ERROR: the factorization has produced a singular U with U[2][2] being exactly zero.
I am running a 3D TOUGH3 model with EOS7C and the AZTEC parallel iterative solver. Occasionally I receive this error that ends my model run, and the OUTPUT file gives me no clues as to what is going…
- Erik W
- Erik_W
- 1 mth ago
- 1 reply
- 12
- kenny1 mth ago
- TOUGH3
Infinite Acting Aquifer
I have a TOUGH3 model (EOS7C) that is showing signs that the model extent is not wide enough in the East and South directions (pressures increasing over time).…
- Erik W
- Erik_W
- 1 mth ago
- 6 replies
- 16
- Erik W1 mth ago
- TOUGH3
Access violation
Hi I encountered following error. Has anyone experienced this and if so how did it get resolved?
- Yashesh Panchal
- Yashesh_Panchal.1
- 1 mth ago
- 1 reply
- 14
- kenny1 mth ago
- TOUGH3
Time-Dependent Material Properties
Hello, Is there a way to implement time-dependent material properties (block ROCKS) in TOUGH3? I am interested in assigning time varying permeabilities (prescribed as a function of time).…
- Nelson Molina Giraldo
- Nelson_Molina_Giraldo
- 1 mth ago
- 4 replies
- 16
- Nelson Molina Giraldo1 mth ago
- TOUGH3
eco2m Fortran runtime error
I have been getting the following error when beginning a TOUGH3 run using the eco2m eos: TOUGH STATUS: Total preprocessing time = 17.409522771835327 At line 3180 of file…
- Ken Glover
- Ken_Glover
- 2 mths ago
- 2 replies
- 21
- Ken Glover2 mths ago
- TOUGH3
TOUGH3 installation issue
I realized many people have difficulty in compilation of TOUGH3. After polishing the installation cmake scripts and reorganizing the installation package, compilation of TOUGH3 should be more easy,…
- kenny
- kenny
- 3 mths ago
- 50
- TOUGH3
COM2 injection with eco2m eos
I have not been able to find any documentation on how brine injection is handled when using eco2m. NaCl is COM2 in the GENER block. I would assume that salt mass fraction of the brine would be part…
- Ken Glover
- Ken_Glover
- 3 mths ago
- 1 reply
- 29
- Ken Glover3 mths ago
- TOUGH3
Can TOUGH3 model temperature below zero degree?
Hi All, I am new to TOUGH and plan to use it in modeling a borehole thermal energy storage system. However, the ground temperature surrounding the system may drop to below zero degree.…
- Haiyan Zhou
- Haiyan_Zhou
- 3 mths ago
- 4 replies
- 37
- Haiyan Zhou3 mths ago
- TOUGH3
Error compiling TOUGH3
Hello, I am trying to compile TOUGH3 in Ubuntu (Windows subsystem for Linux 2), ./complie_T3_Linux.sh 1 I get an error message "Script ERROR: Failed to build TOUGH TPLS" at "Performing configure…
- Hwajung Yoo
- Hwajung_Yoo
- 5 mths ago
- 2 replies
- 71
- Hwajung Yoo1 mth ago
- TOUGH3
creating T2Well .exe from source code
Hi, I have access to a T2Well and TOUGH3 license and would like to have a go at generating the executable from the T2Well source code. I can see in the T2Well/ECO2N manual that there is an NMAKE…
- Hannah Doran
- Hannah_Doran
- 5 mths ago
- 2 replies
- 44
- Hannah Doran5 mths ago
- TOUGH3
Compressibility On/Off in ECO2M
Hello folks, I posted a similar thread on TOUGH2, but here in TOUGH3, there seems to be an option under MOP2 where we can turn on/off the effect of compressibility on porosities.…
- Nur Wijaya
- Nur_Wijaya
- 6 mths ago
- 1 reply
- 29
- Christine Doughtymoderator5 mths ago
- TOUGH3
EOS7r incompatible with mesh
I am a toddler in using TOUGH, I have generated mesh using gmsh converted to tough by toughio. The output file does not indicate a major flaw. I really appreciate it if an expert can spare some time…
- Pedram Mahzari
- Pedram_Mahzari
- 7 mths ago
- 5 replies
- 36
- Pedram Mahzari7 mths ago
- TOUGH3
Parallel Output in TOUGH-3
Good Morning, I have recently started to experiment with using TOUGH-3 in parallel. When I output the simulation variables in CSV format, it seems to print certain parts of the simulation grid twice…
- Gareth Williams
- Gareth_Williams
- 7 mths ago
- 3 replies
- 55
- Gareth Williams7 mths ago
- TOUGH3
termination criterion following two time steps for which convergence on ITER = 1
Hello, It looks like I am running into this exact issues described on page 44 of the T3 user manual (copied below). What suggestions do you have when this occurs?…
- Yannick Champollion
- Yannick_Champollion
- 7 mths ago
- 3 replies
- 37
- Gareth Williams7 mths ago
- TOUGH3
TOUGH3-EOS7-diffusion
Hello, I am trying to model a salt intrusion in a confined aquifer using TOUGH3 and EO7, following Henry's problem. I am defining initial conditions (with multi 2 2 2 8:…
- Alina Gallardo
- Alina_Gallardo
- 7 mths ago
- 17
- TOUGH3
Drastic fluctuation of pressure vs. time curve
Hi, I simulated a simple model with EOS1, but I got a strange pressure vs. time curve. What may causes the curve fluctuation? The ground water velocity is 10-7 m/s, the production rate is 150 m3/h.…
- Tianjiao Li
- Tianjiao_Li
- 8 mths ago
- 25
- TOUGH3
Values <1.0E-100 included in SAVE file with improper formatting.
When running with tough3-eos3, we noticed that there were some values for air mass fraction (X2) that were below 1.0E-100, but the "E" was not included.…
- Mikey Hannon
- Mikey_Hannon
- 8 mths ago
- 1 reply
- 20
- Stefan Finsterle8 mths ago
- TOUGH3
T2Well (modeling nozzle/Plug in wellbore)
Hi everyone, I have question about ROCKS data block in T2Well. According to the manual, the domain of grid cells that start with "x" indicates wellbore cells filled with porous medium or consisting…
- Refaat G Hashish
- Refaat_G_Hashish
- 10 mths ago
- 1 reply
- 47
- Refaat G Hashish10 mths ago
- TOUGH3
Output results of specific grid versus time
Hi everyone, I wonder if there is a code to extract the output results of a specific grid cell in OUTPUT_ELEM file versus time. Thanks in advance
- Refaat G Hashish
- Refaat_G_Hashish
- 10 mths ago
- 2 replies
- 32
- Refaat G Hashish10 mths ago
- TOUGH3
OUTPUT File Size
Hello, Does anyone know if it's possible to reduce the size the OUTPUT file by not printing the same information printed in the CSV/PetraSim/Tecplot file? For example,…
- Nur Wijaya
- Nur_Wijaya
- 11 mths ago
- 1 reply
- 22
- Mikey Hannon11 mths ago
- TOUGH3
Columns Headings in COFT (T2Well)
Hi, In the manual of T2Well, five variables should be obtained in COFT file. While using T2Well, I find seven outputs per connection without titles. Can anyone help me to identify the output…
- Refaat G Hashish
- Refaat_G_Hashish
- 11 mths ago
- 1 reply
- 42
- Christine Doughtymoderator11 mths ago
- TOUGH3
Mesh Generation in T2Well
Hi, I am a new user of T2Well/ECO2N. I want to start building my model by creating mesh using Meshmaker. In TOUGH3, I am used to using the following execution procedure to build mesh: 1.…
- Refaat G Hashish
- Refaat_G_Hashish
- 11 mths ago
- 45
- TOUGH3

1 2 3 4 Next

TOUGH3

Efficient time stepping with great variability in pumping/shutin period durations

At KCYC=1, EXCEED GENERATION TIME TABLE AT ELEMENT #####

EOS7c and NCG injection

AZ_calc_blk_diag_inv: ERROR: the factorization has produced a singular U with U[2][2] being exactly zero.

Infinite Acting Aquifer

Access violation

Time-Dependent Material Properties

eco2m Fortran runtime error

TOUGH3 installation issue

COM2 injection with eco2m eos

Can TOUGH3 model temperature below zero degree?

Error compiling TOUGH3

creating T2Well .exe from source code

Compressibility On/Off in ECO2M

EOS7r incompatible with mesh

Parallel Output in TOUGH-3

termination criterion following two time steps for which convergence on ITER = 1

TOUGH3-EOS7-diffusion

Drastic fluctuation of pressure vs. time curve

Values <1.0E-100 included in SAVE file with improper formatting.

T2Well (modeling nozzle/Plug in wellbore)

Output results of specific grid versus time

OUTPUT File Size

Columns Headings in COFT (T2Well)

Mesh Generation in T2Well

Categories

Top contributors

Recent activity

Home