-
no runlog.out file for error
Hi everyone, I am a beginner using toughreact. Currently, I am building up a 3 layered single phase model. After I built up everything, the model stop running after 1.8 seconds and shows me error.…
-
Boundary conditions
Hi, I am modeling the injection of fluid into a porous domain through a fault. I have a created multiple zones for the domain(sand, shale and fault) and put an injection well at bottom end of the…
-
TOUGH2 EOS1 viscosity
Hi, All I am using the EOS1 module to simulate fluidized sand mixing with water. I have read the tough2 manual. It seems like it is not available to modify viscosity,…
-
CEC: cation exchange capacity (meq/100 g of solid).
In ToughReact, does the cation exchange capacity have the time vector?Does it represents meq/100 g of solid/s?
-
Does the ExtraCell function run well
I want to simulate a small flooding, the core is tiny and I want to add an ExtraCell, where can I find the manual about the meanin of the parameters?
-
Convergence on ITER=1
I'm running TOUGH EOS1 SC, attempting to modeling deep (7km), low permeable basement rock with an intrusion. The combination of heat and low permeability makes it quite a mission to get this baby…
-
Running with MINC and non-MINC elements
In a post I submitted to the TOUGH2 forum ( https://tough.forumbee.com/r/m2fgt1 ), Stefan Finsterle provided me the following steps for running a simulation with both MINC and non-MINC elements in…
-
"Inactive" MINC elements
I want to make sure I'm interpreting the manual correctly as it pertains to "inactive" elements in a mesh involving MINC processing. If I place a dummy element in front of all elements that I want…
-
Polygonal mesh model runs much slower than regular mesh
I'm running CO2 injection with regular and polygonal mesh model, polygonal mesh even has less elements than regular mesh cause of number of connections limitation,…
-
How to use TECPLOT for interpreting T2 OUTPUT
Dear team, I have a difficulties to interpret T2 output (P-T distribution) by using TECPLOT. I created 3-D model of geothermal reservoir with 968 elements. I got error after run the ext.…
-
TOUGH+Hydrate to Tecplot
Since, there is an option to generate tecplot ready file by changing the value of MOP(19), I tried using that to generate the Plot_Data_Elem file, but Tecplot RS doesn't recognize the file.…
-
TECPLOT output from TOUGH+
@Stefan Finsterle Hi, Stefan I know it is not right to talk about some questions relevant to TOUGH+ in this TOUGH2 section, but there seems like no active people in TOUGH+ section.…
-
Compiling TOUGHREACT V3.0-OMP using Cygwin and gfortran
Hey everyone, I have so far been able to compile all EOS modules of TOUGHREACT V3.0-OMP using gfortran and the Cygwin Windows utility. This was done using the following options:…
-
Convergence problem with different mesh size
Dear Sir or Madam, Sorry to disturb you. I was running a simple 1D transport model with surface complexation, but it never ends. However, I found it worked when I increased the mesh size from ∆x =1.…
-
Pore compressibility issue in EOS9
Hello. I have a quick question about EOS9. Normally, the pore compressibility is used for considering specific storage due to pore volume change in TOUGH (at the MULTI subroutine).…
-
Convergence problem for the surface complexation model
Dear Sir or Madam, Sorry to disturb you. I am Lang. I created a 1D transport model with surface complexation. I found it could not achieve convergence,…
-
Post and Pre-Processing free codes for TOUGH2
Hi everyone, I`m trying to download the free codes developed for TOUGH2 post and pre-processing parts but all the links are broken on the National Berkeley Lab website.…
-
Non-isothermal models in EOS 7C
Hi All, I was trying to run the example 2 model that is included in TOUGH 2-EOS7C under a high temperature and pressure condition (100C and 30MPa) using the non-isothermal option.…
-
Creating an angled domain
Hi, I want to create an angled domain to represent a fault as shown in the figure in color red. I'm using Meshmaker v1.5 to create the mesh. So far, I have managed to create a vertical domain for…
-
Empty FOFT file
Hello, I was wondering if someone could help me with the following problem. I am running ToughReact1.2(eos3) and would like to use the FOFT keyword to obtain time-dependent data for selected…
-
Sensitivity Analysis
Dear All, After running a CO2 injection model, I performed a sensitivity analysis to determine the sensitivity of my model with respect to some key input parameters (i.e.…
-
9.4 Problem No.4- Five-spot Geothermal Production/Injection(EOS2)
Dear all, I have been studying and trying to run this problem example in the manual cause it is similar to my Project. I'm trying to view the simulation results using TOughViewer.…
-
The difference depending on the position of the well
I am doing simulation of methane gas recovery using TOUGH 2 EWASG. I created a three layer model of paleogene, cap rock, cretaceous in order from the top.…
-
Error 'Program received signal SIGSEGV: Segmentation fault' after increasing MGTAB
Hi, I increased the MGTAB value in the T2 file to 9000 and recompiled the code. However, when running I receive this error message: Program received signal SIGSEGV:…
-
how to define MOP
Hi all, I am a very fresh user and have some difficulties specifying MOP . TOUGH+ manual contains few examples of input files. I have read those and found myslef completely confused about which part…