-
INCON not creating correctly from INPUT (very new user)
Hello! I am in the early stages of learning how to run TOUGH2. I have been provided an INPUT file (titled "sam7c3"). When I try to run the program, I get an error in the OUTPUT that states "CANNOT…
-
Time dependent DELV (PI/BH)
Dear community, I am trying to use a DELV source type to match some well data. However, every well start at producing at a different time. Then, it is needed to make them available at different times.…
-
Questions Regarding Local Refinement and Mesh Size Limitations (number of elements)
1. Local Mesh Refinement I am importing my mesh from ECLIPSE and not using the MeshMaker utility. I would like to apply local refinement, similar to the approach shown in the snippet below.…
-
How to implement anisotropic permeability tensors and unstructured mesh in TOUGH3?
Hi everyone, I'm working on a model involving complex geological structures with anisotropic flow behavior, and I'm planning to use TOUGH3 because of its support for full permeability tensors and…
-
Subject: Seeking Examples of TOUGH2-FLAC3D Coupling
Dear Professors/Colleagues, I am a researcher in geological engineering, currently conducting multi-field coupling numerical simulations. I urgently seek TOUGH2-FLAC3D coupling examples (e.g.…
-
TOUGH+ 3D model fails to run after uniformly scaling down the mesh
Dear friends, I am currently conducting TOUGH-FLAC3D coupling calculations. I constructed a 100 × 50 × 50 model using FLAC3D, with 15, 7, and 7 grids in three directions respectively.…
-
*** PETSC Solver failed to converge *** in parallel mode (TOUOGH3_v1.12- EOS1)
Hi, I have a problem with code parallelization. The code runs smoothly on my laptop, but as soon as I move to the HPC and use multiple processors, it says *** PETSC Solver failed to converge ***.…
-
ECO2M CO2 Injection in Sandstone - Convergence Failure
help! TOUGH2 ECO2M simulation of CO2 injection into sandstone reservoir fails convergence after initial steps. Adjusted timesteps/parameters unsuccessfully.…
-
Help Needed: EOS3 Non-convergence in Compressed Air Injection into Aquifer
Help! TOUGH2 EOS3 simulation of compressed air injection into aquifer fails after few steps. Adjusting parameters/time steps didn't work. Seeking root causes & debugging tips!
-
T2WELL/ECO2M phase transition issues
Dear TOUGH community, I am trying to model CO2 injection into a saline aquifer. I have a model using T2WELL/ECO2M for coupled modeling, but there is a problem with convergence......…
-
TOUGHREACT Flow Monitoring
Hello, I am a new user of TOUGHREACT and am currently working on a simple problem of injecting CO2 into an aquifer. Is there a way to track the flow of fluids and heat between boundaries,…
-
Reactive transport is off but still looking for solute.inp
I am trying to run a 2D model using TOUGHREACT v4.13. I have the reactive transport off but it still looks for the solute.inp when I run it. Any suggestions how to fix it?…
-
Nucleation reactive surface area
Hi all, I'm running some models where calcite is not initially present but precipitates kinetically during the simulation. There is an option to have initial reactive surface area be very large at…
-
Changing the number of COFT and FOFT
Dear TOUGH community users, I use TOUGH2 and specified over 100 elements and connections for FOFT and COFT. Those FOFT and COFT are exactly written in the input file.…
-
Running MINC model with TOUGHREACT (or iTOUGH2)
Hello, I am trying to run MINC model which includes elements' name in 8 characters with TOUGHREACT, but it can't run successfully. Is there any method that I can follow to run TOUGHREACT with MINC…
-
Compiling T2Well-ECO2N Using Visual Studio 2022
Hello everyone, I currently have the source code for T2Well-ECO2N, and I had previously succeeded in compiling it using Visual Studio 2017. However, since I can no longer install VS 2017,…
-
Invitation for TOUGH4 testing
TOUGH4 is the next generation of TOUGH codes, featuring numerous advancements and enhanced modeling capabilities. More information can be obtained from the following webpage: https://lbl-2.gitbook.…
-
TOUGHREACT/EOS5 serpentinization
Hello All, Is TOUGHREACT / EOS5 able to simulate the process of serpentization that can lead to the production of natural hydrogen? I know that EOS5 is intended for transporting hydrogen in the…
-
TOUGH3 Installation Fails Due to BLAS Package URL Change
I am writing to seek your assistance with an issue I encountered during the installation of TOUGH3. The installation process fails due to a recent change in the URL of the BLAS package,…
-
Changing the boundary water chemistry for a restart run (I think inchem is not read)
I'm trying to model a feedzone and ran the first 23 yrs (upto 7.569e8) and then will restart to run for another 2 yrs (upto 8.1994e8) using a different chemistry for the boundary water (injection).…
-
Thermodynamic Database for CO₂ Storage in Icelandic Basalts
Hello everyone, I've been running sample problem 5 on CO₂ storage in sandstone using TOUGHREACT V3.32. I'm interested in running this problem considering a basaltic formation, however,…
-
How to debug tough3 correctly
I want to debug this code. When configuring tough3-eco2n, the command used is"/configure.sh --build-type=DEBUG --eos=eco2n --no-x11 --petsc-dir=/home/zhigao/petsc-3.17.…
-
How should the enthalpy be correctly specified when simulating the process of air injection into an aquifer using TOUGH3/EOS3?
Hi I am currently attempting to conduct a simulation for CAESA, specifically modeling the process of air injection into an aquifer. Due to persistent convergence issues,…
-
Pressure Drop When Allowing Dissolution/Precipitation of Minerals
Hello everyone, After I run a pressure initialization on the reservoir (REACT(1) = 2), I see that the gridblocks have pressures within the vicinity of that specific in PARAM.…
-
Simulation of the non-isothermal analysis of co2 injection
Hi, everyone i am now tyring to simulate the co2 injection under the non-isothermal situation byTOUGHREACT V1.2 ECO2N). For simplicity, i cosed the reactive transport in this simulation and focus on…