-
Tough+Realgasbrine
Hi there, I'm planning to attend the short course of Tough+Realgasbrine in September, is it a new module going to be released? Do you have any idea when will it be available? Thanks.
-
Define oil and water production rate for cells
We are using EOS8 modulus to simulate a reservoir with oil and water 2 phases. For the production well, there are oil and water production. How do we define the oil and water rate for the…
-
Do you have a recommended module to simulation gas condensate reservoir?
It's a deep gas condensate reservoir, what's module is good for it? What about EOS7C? Thank you very much
-
Hi everybody, I have a question regarding a particular simulation (I am using Petrasim). Can you help me?
Hi everybody, I have a question regarding a particular simulation (I am using Petrasim). Can you help me? I am trying to simulate the heat and fluid flow within a volcanic edifice.…
-
Circulating same produced fluid
Hi I am using TOUGH2-ECO2N module for CO2 injected into brine filled reservoir. I am trying to simulate where the produced fluid has to be circulated back into the system.…
-
Gas relative permeability: equation ???
Hello everybody, I have one question regard the document Tough v2, in "tough v2.0 manual" , we assume krg=1-krl if Sgr=0, we found that this is very strong assumption and which is not confirmed by…
-
Error on installation
I'm trying to install TOUGH2 for EOS2 and I'm having trouble in the compilation. I'm not sure if the code is right and when I type it, I receive this message.…
-
MINC Varying Fracture Spacing
After reading the manual, I can't tell if it is possible to vary the fracture spacing between different gridblocks using MINC in TOUGH2. Is there a way to do that? Thanks, John
-
Suggestion in change the GENER
Hi, Dear all, I want to add a feature about delaying / shutting the production well with wellbore deliverability modulue. The manual said the production well with wellbore deliverability can not be…
-
EOS7C - time stepping problem
Hi everyone, I am using the EOS7C to simulate a pumping test (production well) in coal seam gas aquifer with hydraulic fractures. I used automatic time stepping (MOP (16) = 2),…
-
about the output files of TOUGH-2: EOS9nT
For our research project I need to simulate the radioactive waste transport problems with EOS9nT. I am just at the beginning with learning EOS9nT, however, I have the problem about its output format.…
-
perm. factor
dear all, I want to ask the "perm. factor" in "set cell data", (ex: I want the domain area's K field mean=1E-13 and standard deviation=1E-14) Does it means that I can use Excel to generate a random…
-
Disappearing gas phase during simulation of CO2 injection
Dear all, I am trying to simulate an injection of CO2 into a brine saturated aquifer with Toughreact 1.2 and ECO2N EOS module (1D, radial). Everything works fine until the gas saturation Sg in the…
-
Lower limit of mesh grid?
Hello, I have the following problem by creating a mesh grid with Meshmaker: XYZ NX 20 0.0004 NY 2 1.0 NZ 20 0.0004 or XYZ NX 20 0.125 NY 2 1.0 NZ 20 0.…
-
time step control
Hi! Is there any way to make a simulation going on even if convergance occured on the first itteration for 10 time steps in a row ?
-
why the SAVE disk file is empty even i have no error message when i run the input file
hi all, i am learning tough 2 i found some training courses and tried to exercise i am interested in a Sample Problem 2DVZ: Infiltration Test in the Vadose Zone i tried to write the input file when…
-
what is the suitable EOS ?
Hello, I am a very beginner using TOUGH2 i will use it to simulate the water flow the vapour transport and the heat transpot in a vadose zone in semi arid region what is the suiltable EOS nimber is…
-
Well Connection
Hello. I am a student and relatively new to TOUGH2. I am trying to create a model with a series of six boreholes, each containing a u-tube shaped pipe and all the pipes are connected along the…
-
Why a simulation with "same" input file once runs and once crashes?
I made an input file which worked properly. I just added data block FOFT, and I recieved error by running that. I deleted data block FOFT but with the same input file which previously had worked…
-
Whether can TOUGH2 be used to simulate DNAPL spill (non volatile) in the vadose zone (non volatile oil, water and air phases)?
Hello everyone, I am trying to find a simulator that can simulate DNAPL spill in the vadose zone. The DNAPL is not volatile, but it can be dissolve into water.…
-
Permability factor
hello, Is it possible to upload to PetraSim "cell data" from external file? specificaly, i'm interesting in distributed "Perm. factor". i want to refrain from changing it manually to each cell. ideas?
-
Doubts about the integrated finite difference method (IFDM)
Hello everyone, I am conducting a comparative study between the TOUGH and DARTS simulators. I went through the basic documentation to understand how both simulators work,…
-
Converting single porosity mesh into dual porosity (dual-perm) mesh
By any chance, does anyone know a way of converting single porosity mesh elements file into dual porosity (dual-perm) mesh model file (with correct connections)? Would appreciate any feedback.…
-
Can ECO2N simulate the CO2 phase transition?
Hi guys. I have a question about ECO2N. I want to know if ECO2N can handle CO2 phase change. I would like to simulate the problem of liquid CO2 injection into a reservoir,…