-
INSTALL OF TOUGH2
I purchased Tough2 software and i want to run it using PC 64, 8 proccesor, but i couldnot, please can any one you help me in running the software and to run an example,…
-
Using rock type "x" in T2Well
Hi T2well gives you the option to represent your tubular as a bundle of smaller tubes. I was trying to use rock type x (domain) right after the wellhead for representation of the wellhead choke.…
-
Strange pressure output from EOS7C
I have been struggling for several months now to understand how pressure is accounted for in some TOUGH2-EOS7C simulations that I’ve been running. The fact that the code outputs a single “Pressure”…
-
9.4 Problem No.4- Five-spot Geothermal Production/Injection(EOS2)
Dear all, I have been studying and trying to run this problem example in the manual cause it is similar to my Project. I'm trying to view the simulation results using TOughViewer.…
-
EOS4???????? linking between soil water contents and water vapor pressure in a thick unsaturated zone
Dear Stefan and other moderators please i really need your help to figure out what is the best EOS i have to consider the water vapor diffusion and its effects on the water contents with the time in…
-
SAVE file
Hello ! For the case I'm working on, I've created and INCON file filled with cell-by-cell porosities, permeabilities (I,J,K), pressure and temperature.…
-
Steady-state simulation of a low-type geothermal system
Dear TOUGH2 Users Good morning/afternoon This is my first post to this forum and I’d like to receive guidance and help to perform a steady-state natural simulation model of a low-type geothermal…
-
System of equations for EOS4
Hello, I am trying to write the system of equations for EOS4. But one equation is missing. I think it is the relation between mass fraction of water in gas phase (or mass fraction of air in gas…
-
T2Well-ECO2N
Dear T2Well users; Looking for a tool to design CO2 injection aiming at CCS. T2Well-ECO2N software is new to me, I wonder if it is only a 1D simulator?…
-
Defining a multi-layered aquifer in TOUGH2
Dear All, I am trying to simulate a sandstone aquifer capped by two sealing layers (Shale and evaporite), so there are totally 3 layers in my model. I think there are two blocks in the input file…
-
MINC fracture spacing effect
Hi there, we are building a dual-porosity model in tough, I'm not quite understand how will the different fracture spacing affect the simulation result, when fracture volume fraction is the same?…
-
anisotropic permeability for TOUGH3-EOS7
Dear all, I am trying to modify my INFILE (isotropic permeability) to specify anisotropic permeability element-by-element. My original INFILE (isotropic permeability cases,…
-
How to apply this unique Mix of Neuman + Dirichlet Boundary conditions, for Temperature & Pressure, 1-d Problem
Hello everyone I am trying to setup a 1-D validation problem from a research paper for validating experimental results. In short, I need to apply Neuman & Dirichlet Boundary conditions,…
-
Print out of permeability reduction
Hi guys, Anybody out there could send me a piece of advise how to get permeability reduction "k-red" printed out when running Tough2 with ECO2N? I tried a couple of things in "OUTPU" and "SELEC",…
-
Non-convergence when upper boundary saturated in CO2
Hi everyone, I am using the module ECO2N_V2.0 to model the hydrothermal fluid and heat circulation into high-topographic volcanoes. I want to create a vadose zone in the upper part of my mesh.…
-
TOUGH2 Sample Problem
Hello, This is Mo. I just started learning TOUGH2 and iTOUGH2. I am working on Problem No.4 (Five-Spot Geothermal Production /Injection). I am trying to modify the problem to my own problem.…
-
MINC and MIM
Hi All, I'm comparing MINC to mobile-immobile (MIM) models, most of which focus on transport (i.e., with the diffusion as the process connecting the two domains).…
-
How to use TECPLOT for interpreting T2 OUTPUT
Dear team, I have a difficulties to interpret T2 output (P-T distribution) by using TECPLOT. I created 3-D model of geothermal reservoir with 968 elements. I got error after run the ext.…
-
Simulated CO2 injection into aquifers using T2WELL/ECO2M did not run successfully
Dear TOUGH community users, I am new to T2WELL/ECO2M and I am simulating CO2 injection into the aquifer, establishing a model of 0~-900m, the aquifer is located at -750~-800m,…
-
Blank MESH
Hello Stefan! I'm running the sample problems and I'm having a problem with the Heat Sweep in a Vertical Fracture for EOS1 - rvf input file. I'm creating a meshmaker with the characteristics given…
-
Recompiling EOS1 for using LUBAND
I have been trying to run the two water option in EOS1 to differentiate injection during a history match run but I'm not able to get a full run using the linear solvers.…
-
Atmospheric Boundary Conditions
Hi all, I am confused with the boundary conditions that have to be imposed in an atmospheric boundary element for simulating evaporation with TOUGH2 (or TOUGHREACT). In a few slides (http://esd1.lbl.…
-
TOUGHREACT1.2/ECO2N: About the inject rate and maximum pressure
Hi, everyone I'm using TOUGHREACT1.2/ECO2N with Petrasim. I am simulating the injection of CO2(isothermal) at a constant rate of 6.5kg/s(just one GENER)using a rectangle mesh,…
-
CO2 storage in saline aquifer with ECO2N
Hello All, I am working on CO2 storage using ECO2N. In the output file, we have the following variables. "P T SG SS XNACL YH2OG XCO2aq PCAP k-red" How can I calculate the Mobile CO2,…
-
Empty SAVE file
Dear All, I have run the executable tough2 with the input is a DAT file (got it from Petrasim). When I run the simple model, it worked. But when I made a field model in Petrasim and got the DAT file,…