-
Facing difficulty while converting TOUGH+HYDRATE out file to TECPLOT input
I am using Tough+Hydrate , I need to visualize my result using TECPLOT but while converting the Tough output data to tecplot input file I am facing problem. Guidance will be appreciated. thank you
-
Using rock type "x" in T2Well
Hi T2well gives you the option to represent your tubular as a bundle of smaller tubes. I was trying to use rock type x (domain) right after the wellhead for representation of the wellhead choke.…
-
Mace Spice - Make Hot Food | United Spicefruit
The reddish seed covering the nutmeg seed is used to make mace spice. Its flavor, which is more subtle than nutmeg's, is used to flavor bread, meat, fish,…
-
Coupled reservoir-wellbore model initialization (using T2Well)
Hello everyone, I have started using T2Well to simulate coupled reservoir-wellbore problems recently. While initializing the numerical model, I find the following problem;…
-
How can Toughreact V3 data be extracted and input into TECPLOT?
Hi everyone, someone knows how to extract data from Toughreact V3 output results to TECPLOT. Thank you!
-
Define Constant Injection Pressure
Dear all members, I tried to model water injection with defining constant pressure instead of constant injection rate in ECO2N but I encountered no changes in the model.…
-
error compiling TOUGH3 on Ubuntu : Failed to build TOUGH TPLS
Hi All, I tried to compile TOUGH3 on a new server with Ubuntu 20.04 but not successful. (Please refer to the error.png for error screenshot). I have all dependencies installed and their versions…
-
The pressure initialization presents a gradient distribution, but the temperature gradient disappears.
Hello everyone, I have a question. The pressure initialization presents a gradient distribution, but the temperature gradient disappears. The SAVE file shows that the temperature result is a constant…
-
Tough+Hydrate Model Initialization to Steady state : Pressure gradient appears but Temperature gradient disappears
Hello Everyone. I am trying to run the model to steady state. I have a 190 x 1000 model. I fixed the top boundary to 6.5C and 104bar by making the cells inactive I set simulation end time to (10,…
-
ECO2M running stopped, unit temperature and pressure status abnormal
Dear TOUGH community users, The model is established using Ansys apdl starting from 0 m, with the first unit below the surfacecenter serving as the wellhead unit.…
-
Results file not found (ECO2M, TOUGH V2.1), no .csv file generated
Hello everyone, I am solving the TOUGH exercise (ECO2M Example: CO2 Injection Well). After successfully running Tough v2.1. I am unable to view (3D Results) the results.…
-
Artvigil vs Waklert
Artvigil and Waklert are both products of Armodafinil that belong to the drug class Nootropic. These are prescribed to treat extreme sleepiness disorders due to narcolepsy, sleep apnea,…
-
Modafinil for excessive daytime sleepiness
Modafinil is a Nootropic that promotes wakefulness and helps treat excessive daytime sleepiness. It is an effective option that works within 30 minutes of intake and stays active for about 15 hours.…
-
mesh format for TOUCH
Dear community, I am an absolute beginner and have a very basic question about the required mesh format for TOUGH. Is it possible to use unstructured tetrahedral mesh in TOUCH?…
-
Heterogeneous field simulation
I was simulating water injection into oil reservoir with a heterogeneous permeability/porosity field using TOUGH3-EOS8. The heterogeneous permeability/porosity fields were realized by modifying the…
-
Error in installation
Can somebody help in rectifying the error encountered as shown in attached figure. Thank you in advance
-
EOS1 non-convergence
Hello! I am a beginner in TOUGHREACT. I ran it based on the input file provided by the author of a paper. However, when I ran toughreactV2.0, I found that the model did not converge and the program…
-
Reservoir Temperature Change
Hi all, In the current simulation I'm running, the reservoir temperature change is far less significant than I would expect (50 kg/s for 30 yrs with only localized grid block temp change).…
-
PETSC configure command failed-when compile TOUGH3
I got the "PETSC configure command failed" error at compiling TOUGH3. I need some help. Thanks. cd /Users/wuhao/TOUGH3/TOUGH3v1.0/TOUGH3-Code/esd-tough3/build/tpl-build/tpls/petsc/petsc-3.7.…
-
Carbonate cement distribution in 1D model
Hi, tough users I created a 1D model (EOS1) to simulate the carbonate cement. The initial temperature (15-26 C) and pressure (0.2-5Mpa, equal to 500 m depth) distribution are included in INCON file.…
-
Local vs global sensitivity analysis with iTOUGH
Hello everyone, I am currently attempting to conduct a local sensitivity analysis using iTOUGH. After going through the user's guide, it appears that the sensitivity analysis is primarily presented…
-
Help deciding EOS7C or EOS7CA
Hello, I am a researcher looking to model gas (CH4) accumulation beneath a capillary barrier in the shallow subsurface. Currently I have EOS7C available for use but I am considering purchasing TOUGH3…
-
Mesh is truncated-Meshmaker v 1.5
Hello everyone. I am trying to create a mesh, R=200m and Z = -190m. It has multiple layers. I have added all the info and the file runs, but the mesh is created only up to a depth of -94m and no more.…
-
TOUGHREACT and MODFLOW grid
Is TOUGHREACT AND MODFLOW grids interchangeable? Let's say I have a 3D MODFLOW grid for a project and now I want to use the same grid, potential same flow solution and transfer it to TOUGHREACT to…
-
Temperature dependence cation exchange
Hello, I included cation exchange in my simulation, in which I simulate injection of hot (90 degrees C) water into a relatively cold aquifer with the exact same composition.…