-
How should I compile TMVOC and use executable to run a simulation in the Windows 7 operating system?
Hello everyone, I have an executable for TMVOC and I am not sure how to use it to run a simulation. I tried to run problem 7 mentioned in the manual on the Windows 7 PC, but it could not work.…
-
Problem in 3D LNAPL spillage modelling with TMVOC
Hi friends, I am simulating problem r2dl in the TMVOC Manual but in a 3D geometry with the domain size of 220m*120m*20m(depth) with the discretization of 51*51*51 nodes.…
-
Well modeling
Hi everyone, I use TMVOC to model remediation of soils and groundwaters. I first need to model pumping tests and I was wondering how could I precisely model wells and observation wells.…
-
MINC
Hi For modeling the topsoil cracks using MINC, what should be the number of continua? I think that two is fine, but is it? How can I apply the fracture to a certain number of cells?…
-
Mass out problem of Sources/Sinks about drawdown
Hi everyone : I am trying to pump water and create drawdown in TMVOC I have a question about the pump water. My pump water point is below free water level 1m and want to create 1m drawdown.…
-
Running sample problem 7
On page 109 of the User's Guide, it is mentioned that 'Small changes were made in subroutine GXYZ of the MESHMAKER module meshm.f to obtain the domain assignments' but the changes themselves have…
-
Atmosphere boundary thickness
Hi all I am trying to quantify gas emissions into the atmosphere. But the gas diffusion is highly dependant on atmospheric thickness, isn't it? Whats the most reasonable value for this? Stefan,…
-
Debugging
Hello I am running a problem and the simulation was halted at the middle of simulation. Here is the text that I found in the output file. How can I figure out and fix the problem?…
-
"Default porosity" definition
Hi everyone, Just a quick post to ask a simple question: is the "default porosity" POR in ROCKS the total porosity? For instance, total porosity for clay formations is, in general, about 40-50%.…
-
Mole fraction in each phase
I am confused with term mole fraction in TMVOC output file. I think the total of mole fractions in each phase in one element should equal to 1. But, many output sample in TMVOC manual doesn't show…
-
TMVOC-MP
Hi, has anyone run TMVOC module with Tough2-MP successfully? Our current project has big area and needs fine mesh in pay zone, plus the MINC natural fractures,…
-
In-situ oxidation of TCE
I am trying to model the in-situ oxidation of TCE by KMnO4. In particular I want to determine the overall effects of concurrent solid phase (MnO2) precipitation,…
-
Axis rotation
Hi everyone. I want to rotate my axis from y to z. Now I have an input file where my domain is in x-y (constant width as z direction), but gravity is in z direction.…
-
SAVE as INCON: big issue
Hi everyone, There is an issue with the initialisation of the components in place in my output file. The attached file "save_file_run_1" (screenshot from the output file) shows the volume and mass…
-
Capillary Pressure Definition
In TMVOC, is the capillary pressure between two phases i and j: Pc_ij = Pi - Pj or Pc_ij = Pj - Pi ? where Pi and Pj are the pressures in the phases i and j. Thank you in advance, Quentin
-
Steam injection about TMVOC
Hi everyone : I am trying to model the steam injection remediation I have a question about the steam injection rate. My inject point is 5.5m below free water level When I use “0.…
-
Running 2 NGCs
Hi Everyone, I'm new at using TMVOC. I'm trying to run 2 NCGs (Air and CO2). It's a simple model. Just a model of atmosphere (gas only - with NCGs air and CO2) and soil (water only).…
-
Viscosity of a pure VOC - Error in the formula
Hi everyone, A quick post just for you to note that the formula (4.3.12) in the TMVOC user's manual is not correct. It should be written : ln(µ) = A + B/T + C*T + D*T*T instead of ln(µ) = A - B/T +…
-
Methane Parameters
Hello, would anyone have this information: I am looking for what parameters to use in order to model Methane as a VOC in TMVOC. We have looked in the program files for this information and have not…
-
How can I stop water movement in TMVOC?
How can I stop water movement in TMVOC? I was told to put the residual water saturation of the material, which I think is CP(2), equals water saturation of cells.…
-
Problem with two VOC
Hello, I've run my model with one VOC (aa.dat) without a problem. But, when I tried to use two VOC (ab.dat) in my model, it didn' t work. Could you help me?
-
Oxidation extension
Hi all What are the possible ways to add oxidation extension to TMVOC? Is there any available code like TMVOCbio? Thank you
-
Partitioning Tracer Test Modeling with TMVOC
Hi everyone, I was wondering how could I manage to model Partitioning Interwell Tracer Tests (PITT) with TMVOC. The main difficulty I am confronted by is the data of the partitioning and…
-
Error: Grid Blocks with Erroneous Initialization
Hi everyone, I have started using TMVOC for 3 days, or at least trying :) I have the very same error at the ITERATION step for the sample problems n°2.rblm and n°3.…
-
MGTAB
Hi I am trying to run a domain containing numerous generation sources (>1000). I have faced an error about the number of generation sources. I searched for "MGTAB" in source codes and I found in…