-
How should I compile TMVOC and use executable to run a simulation in the Windows 7 operating system?
Hello everyone, I have an executable for TMVOC and I am not sure how to use it to run a simulation. I tried to run problem 7 mentioned in the manual on the Windows 7 PC, but it could not work.…
-
non-convergence issue
Hi everyone, I'm running a 2d radial case in petrasim where I'm heating from the top, bottom and one side. I first tried to define an extra cell and connect all those boundary cells to it and then…
-
Limitation to the number of VOCs ?
Hi everyone, I am currently running simulations with 8 VOCs (plus air and water) and I want to add 6 more VOCs. I modified the T2 file like so: - MNEQ = 17 (16 components + one energy balance…
-
Well modeling
Hi everyone, I use TMVOC to model remediation of soils and groundwaters. I first need to model pumping tests and I was wondering how could I precisely model wells and observation wells.…
-
Running sample problem 7
On page 109 of the User's Guide, it is mentioned that 'Small changes were made in subroutine GXYZ of the MESHMAKER module meshm.f to obtain the domain assignments' but the changes themselves have…
-
TMVOC initial conditions Convergence Failure
Dears, I am trying to use TMVOC through Petrasim interface to build the attached conceptual model, but when I try to build such model I always have a convergence issues. P.…
-
assigning the right enthalpy
Hi All, I'm running a thermal simulation using TMVOC where I'm also including a mass rate at the second layer beneath the atmospheric boundary layer. The mass rate represents annual precipitation.…
-
Steam injection about TMVOC
Hi everyone : I am trying to model the steam injection remediation I have a question about the steam injection rate. My inject point is 5.5m below free water level When I use “0.…
-
Running 2 NGCs
Hi Everyone, I'm new at using TMVOC. I'm trying to run 2 NCGs (Air and CO2). It's a simple model. Just a model of atmosphere (gas only - with NCGs air and CO2) and soil (water only).…
-
MINC
Hi For modeling the topsoil cracks using MINC, what should be the number of continua? I think that two is fine, but is it? How can I apply the fracture to a certain number of cells?…
-
Problem with two VOC
Hello, I've run my model with one VOC (aa.dat) without a problem. But, when I tried to use two VOC (ab.dat) in my model, it didn' t work. Could you help me?
-
injecting VOC mass through virtual cells
Hi everyone, I am trying to simulate a 1D diffusion scenario where the domain is a column comprised of 200 grid cells (domain is 1m*1m*20m with 200 cells in z-direction) and every grid cell has been…
-
RELP as a function of a VOC mole fraction
Hi everyone, I would like to make the relative permeability of the gas phase a function of the mole fraction of the the first VOC. Actually, the first VOC, in this case,…
-
Mass out problem of Sources/Sinks about drawdown
Hi everyone : I am trying to pump water and create drawdown in TMVOC I have a question about the pump water. My pump water point is below free water level 1m and want to create 1m drawdown.…
-
Convergence failure at production well
Hi everyone, I am trying to heat up water and NAPL (atmospheric pressure) with a production well for vapor extraction at cell #341 (atmospheric pressurre and productivity index 1e-10 m3 ).…
-
Temperature limit
Hi everyone, I am trying to model thermal condutive heating in unsaturated soil and I need the temperature to get above 500 degrees C after water dries out.…
-
Using TMVOC or just TOUGH basic (EOS9) ?
Hi, can i know the step for LNAPL spill on top of surface then migrate to the bottom of soil, I just wanna check the saturation of soil and the velocity of LNAPL in unsaturated soil condition.…
-
erroneous initialization
how to solve errors with erroneous initialization? and also the errors regarding temperature out of range?
-
Oxidation extension
Hi all What are the possible ways to add oxidation extension to TMVOC? Is there any available code like TMVOCbio? Thank you
-
Atmosphere boundary thickness
Hi all I am trying to quantify gas emissions into the atmosphere. But the gas diffusion is highly dependant on atmospheric thickness, isn't it? Whats the most reasonable value for this? Stefan,…
-
How can I stop water movement in TMVOC?
How can I stop water movement in TMVOC? I was told to put the residual water saturation of the material, which I think is CP(2), equals water saturation of cells.…
-
How many materials can be included in TMVOC?
Hi everyone! These days I am trying to use TMVOC to simulate DNAPL spill and redistribution in a heterogeneous medium. However, I found that there seemed to be something wrong with my code.…
-
crashing after reaching equilibrium and starting VOC injection
Hi everyone, I am simulating a 3D sand pack test where it is half full of water with some small hydraulic head from one end to another and the oil leaks into the sand at some distance above this…
-
CHEMP block for diesel and gasoline?
Hello, does anyone know where I can get access to a CHEMP block for diesel fuel and gasoline? Preferably, reference documents justifying the parameterization would also be helpful,…
-
In petrasim, how to enter the atmospheric pressure by file?
In the petrasim, how can i enter the pressure by Sine?In other word ,I want to set the pressure via sine function. Thanks a lot! Sincerely!