-
Large Size of Plot_Data_Elem file
I am getting very large Plot_Data_Eleme output file (20 GB). Is it normal? Is it possible to get this file only for certain time interval instead of all time steps?
-
TOUGH3-FLAC3D time step setting
Hi, I am trying to couple TOUGH3 and FLAC3Dv7.0 through python scripting engine built in FLAC3D software. I am confused about the time step control after reading some published papers (e.g.…
-
How to Add Velocity Parameters in TOUGH3 Input file (.dat file)
Hello Everyone Here I have attachted my TOUGH3 input file, I want to edit this input file by adding Velocity parameter in which TOUGH3 internally calculates it as output.…
-
No error, nothing... Why this file refuses to Run? Tried everything, but it just wont run.
I am modeling a R-Z system(100-X, 190-Z). There are just three layers, TOPSD, BOTSD, and HYDRL, apart from thin top and bottom cell. Everything is setup correctly.…
-
cguess and ctot in chemical input
Dear all, I would like to ask what does cguess and ctot mean in the chemical input in ToughReact? I have read the user guide, I have also searched in papers and still haven't found an answer what…
-
crashing after reaching equilibrium and starting VOC injection
Hi everyone, I am simulating a 3D sand pack test where it is half full of water with some small hydraulic head from one end to another and the oil leaks into the sand at some distance above this…
-
Facing problem to set boundary conditions
Hello TOUGH User Forum, I am Asma Recently, working on TOUGH3 simulation Here I have attached a TOUGH3 Input file (TOUGH3_Structure_Simulation.dat file) which is extracted from Leapfrog TOUGH after…
-
Vector flow maps using PyTOUGH
Hi All, Can anyone tell me, how to plot flow vectors using t2listing class? I can easily plot scalar field from my results using layer_plot method, but do not know what to assign to flow attribute of…
-
changes in chemical.inp
Dear all, I am a totally new Toughreact user so please forgive me if my question is a bit stupid. I want to modify the chemical.inp from one of the Toughreact examples (1d-CO2).…
-
Heat generation in EOS3
Hello, I am a relatively new TOUGH2 user. I have developed a model for heat and fluid flow in a basin with a lake. I am attempting to have atmospheric boundary conditions are the top of the model…
-
Declining steam cap pressure
Dear TOUGH community, I am modeling a liquid-dominated geothermal reservoir underlying a steam cap. In the natural state I was able to match the cap pressure providing mass by means of several…
-
Can TOUGH3 EOS7C model temperature below 13 celsius degree?
I am modelling groundwater and gas migration using TOUGH3 EOS7C. I set up the model as an isothermal problem with a constant air temperature 5 degree (temperature assigned for atmospheric elements)…
-
How to calculate what portion of a constituent adsorbs.
Hello there, I ran a 1-cell chemical initialization simulation that includes surface complexation for 1000 years. For some constituents such as Cr, the total sorbed moles are more than their initial…
-
Methods to Place GENER Block
Hi, What is the fastest method that people use to identify the placement for their GENER blocks? For example, I want to place multiple wells as producers at a specific depth and injectors at another.…
-
Run ends early
Hi, I was working on a larger block mesh using a doublet configuration for an aquifer, over 10 years. When I made the mesh finer, the simulation timed out and quit after 16 hours.…
-
Stopping in main due to flow nonconvergence
Hello everyone, I am using ECO2N to simulate CO2 injection into a formation with relatively low permeability. I am having trouble with an error popping up.…
-
How to define the characteristic length (lc) for the extruded mesh?
Dear Community, Using TOIGHIO, this code extrudes a 2D mesh into a 3D mesh along the y-axis. mesh.points[:, [1, 2]] = mesh.points[:, [2, 1]] mesh.extrude_to_3d(height=100, axis=1,…
-
OUTPT section
I use cubes to construct an octahedron prism. The cross-section shape is shown in the attachment. The largest distance in three directions is 41, 41, 291. How do I write the OUTPT section? Thanks!
-
Defining Tortuosity
How to insert the tortuosity in Petrasim software?
-
TReactMech Simulator!
Hello, I am working on CCS research. I am wondering if the TReactMech simulator is available. I have seen it in papers, but can't find it the on LBNL marketplace. Please advise! Thanks. Nicholas
-
Training
Is there any training for tough2 or tough3 for beginners?
-
Training
Hi all, Is there any training in UK or online for beginners as I need to get to use Tough2 and add Flac3d to it later
-
Radial heat transfer with MOP(15)=5
I plan to simulate fluid flow in a discretized wellbore (discretized with volume elements on a radial mesh) using ECO2M with heat transfer between wellbore and the surrounding formation.…
-
van Genuchten - Mualem model
I am reviewing the RPCAP keyword with the G-M model (7). There are recurring terms Sl, Slr, and Sgr that are not defined in the User Manual. I understand "irreducible water saturation" is Slr.…
-
The problem of using toughio to process input files
Hello Here is a test input file that can run normally(r2dl1). But when I use toughio to read and write, the output file(r2dl1_new) cannot be executed correctly. parameters = toughio.…