-
Monte Carlo simulation crash using iTOUG2.
Hi, I have a problem using iTOUGH2. when I try Monte Carlo simulation with a model containing MINC. The Tough2 input file contains the 'MINC' keyword, and I have a file called 'MINC' generated by…
-
Database TherAkin10.dat
I need some information about the thermodynamic data from TherAkin10. For example what means k-feldspar k-feldspar-kk or magnesite and magnesite-2 and why is the Log K much greater for magnesite-2
-
Estimating water saturation in a water zone above steam-heated bitumen.
A Steam-Assisted Gravity Drainage project is proposing to use water from a water zone over a bitumen reservoir, for steam injection into the base of the bitumen pay zone.…
-
What are the differences between the regular, stand-alone TOUGH2 code and the TOUGH2 forward simulator used in iTOUGH2?
(this is just a test of the TOUGH User Forum)
-
What does the core module do?
- Answered
-
How do I know which module I need?
- Answered
-
Tapaday 100mg
tapaday 100mg Tablet is used to treat moderate to severe pain, such as toothaches, headaches, and joint and muscular disorders. It works by inhibiting chemical messages in the brain that inform us…
-
In ECO2N, the injected co2 gas is mixed with a certain amount of so2
hello: I would ask how the injected co2 gas in ECO2N contains a certain amount of so2. Is the setting method like me correct. Thank you for the reply. Thank you
-
ECO2N(I would like to ask what figure CO2 means? Why is the mole fraction greater than 1?thanks)
I would like to ask what figure CO2 means? Why is the mole fraction greater than 1?thanks
-
Initialization problem for ECO2N Problem No. 4 (rtp7)
Hello everyone, I'm new to TOUGH2.In running the fourth example of ECO2N, I don't understand how to set the initial conditions. 1. The manual mentions only involving boundary grid cells with…
-
Unable to execute code due to plugin not found?
Hello everyone, how can I solve this problem? I tried downloading the corresponding plugin but still couldn't solve the problem.
-
Facing difficulty while converting TOUGH+HYDRATE out file to TECPLOT input
I am using Tough+Hydrate , I need to visualize my result using TECPLOT but while converting the Tough output data to tecplot input file I am facing problem. Guidance will be appreciated. thank you
-
The pressure initialization presents a gradient distribution, but the temperature gradient disappears.
Hello everyone, I have a question. The pressure initialization presents a gradient distribution, but the temperature gradient disappears. The SAVE file shows that the temperature result is a constant…
-
mesh format for TOUCH
Dear community, I am an absolute beginner and have a very basic question about the required mesh format for TOUGH. Is it possible to use unstructured tetrahedral mesh in TOUCH?…
-
Error in installation
Can somebody help in rectifying the error encountered as shown in attached figure. Thank you in advance
-
EOS1 non-convergence
Hello! I am a beginner in TOUGHREACT. I ran it based on the input file provided by the author of a paper. However, when I ran toughreactV2.0, I found that the model did not converge and the program…
-
Temperature dependence cation exchange
Hello, I included cation exchange in my simulation, in which I simulate injection of hot (90 degrees C) water into a relatively cold aquifer with the exact same composition.…
-
How to set up well bore
Hi TOUGH community, I am trying to incorporate a well bore into my simulations in TOUGHREACT, and I am confused on how to set up my mesh. Please, kindly Assist.
-
The pore pressure decreased near the non-reservoir wellbore during the CO2 injection process
Dear TOUGH community users, When I used T2WELL/ECO2N to simulate carbon dioxide non-isothermal injection, I found that when using cryogenic supercritical CO2 injection,…
-
Speciation with brine using Pitzer
I am trying to run a simple speciation problem with a brine composition in contact with some minerals (like Albite, Barite, Illite, K-feldspar etc.). The idea is to use the results of the speciation…
-
Two phase flow (Diffusion vs advection) with mesh sizes
Dear all, dear Finsterle, I have a question regarding the mesh size and its impact on diffusion in two-phase flow. I'm curious to know if the mesh size affects the diffusion from element0 to element1.…
-
how to use RESTART to inherit the minerals fractions and change P T?
Hi, My model is 1D with 10*10*400 meter. Firstly, I renamed the save and savechemical to INCON and inchemical in the first simulation, and copied these two files to the second simulation folder.…
-
low injection rate can induce the EOS CANNOT FIND PARAMETERS?
Hi,everyone I want to simulate the dissolution and precipitation induced by meteoric water injection (toughreact332_EOS1). I set injection rate 9.5129E-02 kg/s during 2Ma,…
-
Where to find input files for Tough+Hydrate v1.2 version, other than the ones in the manual?
Hi everyone, Does anyone know of a website where I could find input files of 1.2 version in order to compare to the examples in the manual? Or better still, can anyone post me their input files?…