-
Running 2 NGCs
Hi Everyone, I'm new at using TMVOC. I'm trying to run 2 NCGs (Air and CO2). It's a simple model. Just a model of atmosphere (gas only - with NCGs air and CO2) and soil (water only).…
-
Compilation mistake
I have been trying to use Tough2 version 2.1 in Windows 7 (64 bit) but it hasn’t worked. I am using the commands gfortran -c -O2 -fdefault-real-8 -fno-align-commons -fdefault-double-8 -funroll-loops…
-
Species appear two times in time.out
Hi, I have a problem in reading result file. Some primary species in <time.out> appear two times; one column with the header of "t_xxx" and the other start with just "xxx" without "t_" ahead.…
-
Is there a limitation in the number of grid blocks to be printed out?
Hi- I ran two simulations with different number of grid blocks to be printed out in 'time.out' The first case with 10 grid blocks had no problem at all but the other one with 100 blocks encountered…
-
(ECO2N)CANNOT FIND PARAMETERS AT ELEMENT * *, for help
Hi,dear all, I'm here agian. I was puzzled by a question for a long time, I appreciate anybody can provide some suggestion. I have attached my input file, MESH,INCON,and the output file,…
-
MINC
Hi For modeling the topsoil cracks using MINC, what should be the number of continua? I think that two is fine, but is it? How can I apply the fracture to a certain number of cells?…
-
EOS7C-running problem
Hi everyone, I am doing a simulation with EOS7C in the heterogeneous coal seam aquifer with water and gas extraction from the well located in the middle of the model.…
-
compile using gfortran
I'm sorry to ask questions so many times, but I can count on only this forum. I read https://tough.forumbee.com/t/80xxf4/install-of-tough2 , and I'm facing the same (Ana Avila 's compiler) problem.…
-
EOS1 - REDUCE TIME STEP error
Hello, I am simulating the single-phase radial flow of water to a well during 13 days of pumping test. I am using EOS1 with MULTI (1,2,2.6). After running the code,…
-
How to assign a permeability for each grid cell?
Hi. I am trying to convert an Eclipse simulation model to TOUGH2. In the Eclipse model each grid cell has a (diagonal) permeability tensor, with a scalar for permx, permy, and permz.…
-
Element Numbering
I am wondering what convention is used for the alphanumeric (described online as AAAII?) element numbering. For instance: cell #1 = 001, cell #1000 = A01, but I'm not able to figure out the pattern.…
-
Problem with two VOC
Hello, I've run my model with one VOC (aa.dat) without a problem. But, when I tried to use two VOC (ab.dat) in my model, it didn' t work. Could you help me?
-
Do you need a pre- and post-processor for tough2? Try GMS.
Do you need or like to work with: Complex geology? Conceptual modelling? Statistical analysis? Original TOUGH2 formats? Then one possibility is to use GMS as a pre-and post-processor.…
-
1d tough2 problem
hi my task is to use tough2 to do 1D simulation in a 10 m thick of unsaturated zone from above the model is objected to precipitation and evapotranspiration so i have a long time serie of weather…
-
Simulation stops automatically at (9999,9)
Greetings, I have developed a field scale stacked reservoir model to simulate the flow and transport of sc-CO2 in the subsurface. In my model, the domain is 1 km in lateral extent and vertically it…
-
How can the relationships between permeability (k/k0) and porosity (Φ/Φ0 ) in the fault be changed?
I am using ECO2N to simulate CO2 leakage in a geological formation with a fault (See the fig). I need to apply different relationships for permeability (k/k0) and porosity (Φ/Φ0) between the fault…
-
How to set up semi-analytical method to calculate heat transfer in t2well?
Dear TOUGH community users, Could you please advise on configuring the semi-analytical method for computing heat transfer in t2well-eco2m? As far as I understand,…
-
Results file not found (ECO2M, TOUGH V2.1), no .csv file generated
Hello everyone, I am solving the TOUGH exercise (ECO2M Example: CO2 Injection Well). After successfully running Tough v2.1. I am unable to view (3D Results) the results.…
-
TOUGHREACT and MODFLOW grid
Is TOUGHREACT AND MODFLOW grids interchangeable? Let's say I have a 3D MODFLOW grid for a project and now I want to use the same grid, potential same flow solution and transfer it to TOUGHREACT to…
-
how to set up initial chemical conditions?
Hello, I've just started using Toughreact, and I am wondering how to set up the chemical initial condition. Should I run a simulation to let TR calculate the brine chemical composition at equilibrium,…
-
Calculated gas pressure despite zero gas saturation
Hello TOUGH2 community, I am running few simulations using EOS5 (water/hydrogen) with injection of hydrogen in a HLRW waste cell configuration. I want to monitor the pressure build-up.…
-
How could charge diffierent boundary water at same model?
I set two types of boundary water in same model. And I want to charge first boundary water into reservoirs during 100-50 Ma, then charge the second one by same boundary elements sicne 50 Ma to…
-
About the regular and radial mesh
Hi everyone, I was using TOUGHREACT V1.2 ECO2N to run a simple injection simulation,and When I set up multiple injection points(such as 5 points and each is spaced 20m apart, that is,…
-
Does TMVOCBio in TOUGH3 have any option for 3-phase hysteresis
Hi all, What I recall is that TMVOC did not have Hysteresis options for three-phase capillary pressure and relative permeabilities (see the link). Seems it is still the case in TMVOCbio (in TOUGH3).…
-
how to debug Tough3 in vscode
Hi all, When configuring, I changed the -- build type to debug, which can generate an executable file called tough3-eco2n in the tough3-install folder. Then,…