-
Define Constant Injection Pressure
Dear all members, I tried to model water injection with defining constant pressure instead of constant injection rate in ECO2N but I encountered no changes in the model.…
-
Any idea for constant thermophysical properties for fluid (water) and P/T decoupling in governing level?
Hello. I'm trying to modify TOUGH2 codes for constant thermophysical properties for fluid (eos1) and P/T decoupling in governing equation level. In order to do this, I've fixed density, viscosity,…
-
CONNECTION in Mesh file
Hi, dear all, I am recently having problems in defining the connected elements in the MESH file. I opened the MESH file, and I found there is error in "CONNE" part (own code in writing the MESH…
-
SAVE file
Hello ! For the case I'm working on, I've created and INCON file filled with cell-by-cell porosities, permeabilities (I,J,K), pressure and temperature.…
-
modelling a river
Hi, What is the best way to define a b.c. for a river (standing water body)? I have leak point at some depth below the bottom of a river within a groundwater.…
-
EOS1 with 2nd water. Some issues ...
Hello everybody, I'm quite new to Tough2, and trying to build my 1st case. So far I managed to run a very simple case with 2 wells (1 producer / 1 injector) in a water filled reservoir.…
-
Enthalpy Discrepancy
Hello There, I was just wondering what the reference state for the enthalpy of water in TOUGH2 is? The reason is I would like to define water infiltration (precipitation) with a temperature of 20˚C.…
-
Flux question
I need to track the mass balance of water through a system and pull it out every step to transfer to a reaction modeling code. Can anyone tell me what array/indexing I can use to get the flux across…
-
Non-Darcy flow of oil above bubble point
In blowout simulations of proposed (not yet drilled) oil wells in the Gulf of Mexico (Worst Case Discharge, aka WCD) a simple radial reservoir simulation model is assumed and flowing pressure bottom…
-
Deliverability model to simulate landfill gas collection systems
Hello I want to model the suction in landfill gas collection systems using Deliverability model. In landfills, we set a suction pressure and it collects the gas.…
-
Non-convergence when considering permeability heterogeneity
Hello again, the non-convergence problem is still unresolved when considering permeability heterogeneity in my TOUGH2/ECO2N CO2 storage model. In this model I used the default/common parameter…
-
MINC processing for fractured media
Dear all Members, Hi, I am working on fluid flow modeling in fractured media and I am using MeshMaker 1.5 to for MINC processing and mesh making. After entering the command codes,…
-
CO2 storage simulation with heterogeneous perm field fails to converge
Hi all, I have a problem with building a geological CO2 storage model using the TOUGH2/ECO2N module. In this model, I considered a heterogeneous permeability field by using the PM-coefficients…
-
Non convergence when considering non-isothermal or molecular diffusion in TOUGH2 ECO2N
I am using TOUGHREACT V3.32 to model CO2 injection in a radial 2D mesh with different layers in the z-direction. Before running the reaction part of the problem I wanted to test the flow part was…
-
bottom flowing pressure well on delivery
Dear All, I would like to get an estimate of the bottom flowing pressure in a well that is cross cutting several layers and sometimes several cells in the same layer (when the well is deviated for…
-
Convergence becomes difficult after CO2 breakthrough (ECO2N)
Hi, I want to know why the convergence becomes difficult (so the time step becomes very small, or simulation terminates) near or after phase breakthrough.…
-
Setting permeability anisotropy with Voronoi elements
I'm trying to define proper permeability values for each connection in my Voronoi mesh file. Essentially, my PER(1) and PER(2) values are constant and equal to one another,…
-
Thermal Expansion Coefficient Of Water
Hello Forum, New poster here so please let me know if I should be looking elsewhere. I'm attempting to verify TOUGH2 against an analytical solution for 2D convective flow and one of the terms is a…
-
Tough2 EOS7C Gas Production Simulation Questions
I use EOS7C to simulate gas production for 2 years. The model includes 1 overburden layer, 1 underburden layer and 1 reservoir layer. After 2 years of gas production,…
-
Boundary conditions
Hi, I am modeling the injection of fluid into a porous domain through a fault. I have a created multiple zones for the domain(sand, shale and fault) and put an injection well at bottom end of the…
-
TOUGH2 EOS1 viscosity
Hi, All I am using the EOS1 module to simulate fluidized sand mixing with water. I have read the tough2 manual. It seems like it is not available to modify viscosity,…
-
Convergence on ITER=1
I'm running TOUGH EOS1 SC, attempting to modeling deep (7km), low permeable basement rock with an intrusion. The combination of heat and low permeability makes it quite a mission to get this baby…
-
"Inactive" MINC elements
I want to make sure I'm interpreting the manual correctly as it pertains to "inactive" elements in a mesh involving MINC processing. If I place a dummy element in front of all elements that I want…
-
MINC and MIM
Hi All, I'm comparing MINC to mobile-immobile (MIM) models, most of which focus on transport (i.e., with the diffusion as the process connecting the two domains).…
-
ECO2N non-isothermal issue
I'm injecting CO2 (at enthalpy 3.09E5 J/kg, about room temperature) to a reservoir having temperature range 50C to 100C, but the temperature at injection cell drop quickly to 3C after injecting that…