-
MINC mesh repeating element ID
Hello, I have a mesh of ~500,000 elements and I am trying to MINC two layers within the mesh. The problem I am having is that after I MINC my primary MESH the I get repeated element ID's in the MINC…
-
How can I simulate the thermal diffusion (Soret effect) ?
Dear everyone, I am New in using TOUGH, i want to simulate the thermal convection of a binary mixture methane & n-butane in non-isothermal condition. I want to take in consideration the soret effect.…
-
How to determine the influence of boundary size?
Hi all, when i use tough2(ECO2N), i'm not sure whether the boundary size i chosen is appropriate, can anybody tell me how to determine the boundary size? thans very much! sawyer
-
Generating initial conditions
Hi All, I am having problems generating initial conditions with the new version of T2ECO2N (v 2.1) that I have just purchased. Previously I would assign a large volume block at the top and base of…
-
Compilation mistake
I have been trying to use Tough2 version 2.1 in Windows 7 (64 bit) but it hasn’t worked. I am using the commands gfortran -c -O2 -fdefault-real-8 -fno-align-commons -fdefault-double-8 -funroll-loops…
-
How to set up source water volume as boundary condition
I have one question regarding how to set up the water source volume in petrasim/tough2. For example, the reservoir is bottom water type. There is water driven at the bottom of the reservoir,…
-
Non isothermal simulations using ECO2N module
I am trying to run some simulations using TOUGH2-MP and compare the results with TOUGH2. The simulation runs successfully by TOUGH2 but when I tried to run it with TOUGh2-MP,…
-
Initial Geochemical Equilibrium between Minerals and Brine
Hello there, I'm simulating CO2 injection into sandstone aquifer of synthetic brine, NaCl. I've read in several papers in which TOUGHREACT w/ ECO2N is used and something is mentioned like "batch…
-
Species appear two times in time.out
Hi, I have a problem in reading result file. Some primary species in <time.out> appear two times; one column with the header of "t_xxx" and the other start with just "xxx" without "t_" ahead.…
-
Well modeling
Hi everyone, I use TMVOC to model remediation of soils and groundwaters. I first need to model pumping tests and I was wondering how could I precisely model wells and observation wells.…
-
Input data file vs Disk Files
Hi All, I am very new to TOUGH2. In my case, I run initial input data file then I have Disk Files generated from TOUGH2 input file after running, these are : INCON, MESH, GENER, SAVE, etc.…
-
A question about the EOS9nT
Hello everyone, I have a question or problem about the EOS9nT in my recent research project. In the attachment you can see the guide example that we downloaded together with the source code.…
-
Difference between 'e' and 'd' in power expression
Hi, it might be a minor problem though (because I am a newbie to scripting), Sometimes the power expressions are written in 'd', not 'e' (e.g. 1.0d-9, not 1.0e-9 especially in DIFUN filed).…
-
Mineral volume fraction greater than 1 in outsolid.dat
Hello, I have a problem with TOUGHREACT PITZER. I'm running a model with calcite, anhydrite and dolomite whose initial volume fractions are 0.99, 0 and 0.01 respectively.…
-
Turbulence in TOUGH2
So I'm doing a bit of modelling on modelling high permeability faults and was getting some large fluxes of fluid (yay!) but.... I was wondering whether TOUGH2 is accurately representing these systems…
-
permeable faults modelling
Hi there, Do you have any suggestion on modelling inclined permeable faults in tough2 model? how to refine faults zone only? Thank you very much Jing
-
Recompiling EOS1 for using LUBAND
I have been trying to run the two water option in EOS1 to differentiate injection during a history match run but I'm not able to get a full run using the linear solvers.…
-
problems running an old TOUGH2 model
Hi. I am trying to run an old model that made by another student last year, and receive the following error message in the command prompt: forrt1: severe <64>: input conversion error, unit 5,…
-
Coupling between flow and processes
Hi there, I am wondering how the fluid flow and heat transport are coupled in Tough2. Are fluid and heat flow equations solved iteratively ? I would be thankful if could help me in this regard.…
-
Documentation on the Numerical Aspects in Forming and Solving the Equations
Hello, There are many papers on Toughreact but I am searching for a documentation/paper on forming the equations i.e. accumulation, convection, reaction terms and solving these equations.…
-
Error in Output File EOS1
Hallo team, I have problem with output result of my current model which is created in Petrasim. I generated TOUGH2 file (.dat) of the model. I tried two ways to get the result:…
-
Mass out problem of Sources/Sinks about drawdown
Hi everyone : I am trying to pump water and create drawdown in TMVOC I have a question about the pump water. My pump water point is below free water level 1m and want to create 1m drawdown.…
-
Does the thickness in y-direction matters when using XYZ to generate X-Z mesh?
Hello everyone, I am using the TOUGH2/ECO2N code to simulate the injection of CO2. I intend to use XYZ MESHMAKER to generate a 2D X-Z mesh. So I want to ask that whether the thickness in y-direction…
-
what is the meaning of the running time is negative?
Hello everyone, can anybody tell me why the running time is negative? As shown in the figure? Thanks very much! sawyer
-
Simulating CO2 injection using EOS2
Hi, I am currently learning to use TOUGH2 and using sample problem 4 (file rfp) as the basis of my work. I was wondering if it's possible to edit the input file to change the feed composition and how…