-
An issue (experience) with very large mesh
Hi all Just to share my experience. I have a very large mesh (6E5 grid cells). Surprisingly the name of some elements start with "END" (like END 1, .. END10 etc).…
-
Mass balance issue on mineral phase during CO2 injection in radial system
Hi everyone, we use a typical case of CO2 injection (see details in Andre et al. 10.1016/j.enconman.2007.01.006) at 200 b in a radial system, so it was using the 2007 version of toughreact.…
-
Compilation of TOUGH error messages
I have started compiling error messages produced by the operating system or TOUGH when something goes wrong. Please add to this list as needed. Christine
-
T2well output files
Hello T2well users; I have just started using the code. I run a case with only a well model (reservoir represented solely by the last grid block at the bottom).…
-
CO2 solubility ECO2n carbonated water
Hi everyone, I'm working on CO2 mineralization in the subsurface where carbonated water is injected into reactive minerals, similar to the CarbFix project.…
-
toughio
Dears, I want to read the file SAVE output from tough+hydrate through the toughio library, but the code runs all the time and fails. How can I solve this problem? Thanks in advance
-
TOUGH3-EOS7-diffusion
Hello, I am trying to model a salt intrusion in a confined aquifer using TOUGH3 and EO7, following Henry's problem. I am defining initial conditions (with multi 2 2 2 8:…
-
No change in minerals vol. fraction
Dear All, I am a beginner in TOUGHREACT simulation and I have issues with getting results from simulation. This simulation performs simulation and there is no error indicated in the runlog file,…
-
Drastic fluctuation of pressure vs. time curve
Hi, I simulated a simple model with EOS1, but I got a strange pressure vs. time curve. What may causes the curve fluctuation? The ground water velocity is 10-7 m/s, the production rate is 150 m3/h.…
-
TOUGHREACT-EOS2 - non-congergence- injection of H2O and CO2
Hey everyone, I need help to solve a problem in my input file, please. I run into a problem with an input file which I have been using for different simulations already and which worked fine.…
-
NaN in TOUGHREACT 3 EOS2 simulations
Hello Everyone, I'm using TOUGHREACT 3 with EOS2. When I run the simulation (which runs well in TOUGHREACT 2) the results are NaN in the aqueous concentrations and minerals.…
-
Using TOUGHREACT with outside flow data
So I think the answer to this is "no", but is there a way to run TOUGHREACT using fixed velocity fields provided by an EOS module from another TOUGH code, like TOUGH3?…
-
Results for Manually Added Minerals
Hello, everyone! In my simulation, there were manually added minerals to the database ( with all necessary data), however, after running and getting results (from Line plot/ export data),…
-
Mesh Generation in T2Well
Hi, I am a new user of T2Well/ECO2N. I want to start building my model by creating mesh using Meshmaker. In TOUGH3, I am used to using the following execution procedure to build mesh: 1.…
-
Solute transport and shift simulation
Hello everyone! I recently used Petrasim2018 to solve the problem of the dissolution and precipitation of minerals. In the 3D results, I found problems with my results, as illustrated in the figure.…
-
ECO2M: Injection under injection-pressure constraint
Hello, I'm running ECO2M to simulate a CO2 injection. Does anyone know if it's possible to simulate the injection under a bottomhole-injection constraint, instead of injection rate constraint?…
-
ECO2M: Halting runs at certain maximum pressure
Hello, I'm running ECO2M and simulating a CO2 injection. I'm interested to see if there is any way I can halt the simulation runs if any of the cells reaches a certain maximum pressure,…
-
ECO2M: Extracting Vector Orientation
Hello, I'm using TOUGH2-ECO2M and interested in extracting the "direction/orientation" of the vector output data (flow of heat, flow of fluid, etc), ideally generated in the same CSV format as in…
-
ECO2M: Meaning of VLIQ at Saq=100%
Hello, I am using TOUGH2-ECO2M, and I have a question about the scalar output parameters “Vliq” and “Vgas”. I’m using PetraSim as the post-processor, and the PetraSim windows shows “Pa-s” as the…
-
Run-time library dependencies
Hey everyone, I’m trying to set up a Docker container, in a Linux like environment, with a TOUGH3 executable in it. When I attempted run the executable, I got a missing library message: .…
-
Mass balance issue during phase change (water -> steam)
Dear users, In TOUGH/ TOUGHREACT when we consider water-steam flow in a pipe (EOS1) and assume at given conditions for pressure and temperature the water changes its phase to vapour.…
-
Sequestered mass of CO2 not calculated/printed out by ECO2N
Hi there, I'm having a look at the example P5_eco2n (TOUGHREACT v332), on CO2 geological sequestration. To my surprise, the sequestered CO2 (output variable 'SmCO2') appears to be zero regardless of…
-
Looking for training sessions of Toughreact using Petrasim
Hi Everyone, I am new user of TR and I have research project that investigates CCS in Kazakhstan. Since the project can cover the training expenses, I would like to ask if anyone can explain how to…
-
Area adjustment factor
I am currently doing some simulations of core based experiments using the kinetic model. With regards to terms in the equations I would like to confirm the notation.…