-
How to create an executable file in TOUGH3?
Hello All, I have TOUGH3 source code and I need to create the executable file that runs in command window. I wonder if somebody can help me with that issue. Best regards, Shirin
-
iTough2_ECO2M
Hello, I`m struggling with the ECO2M sample 4(*rwaf*) and hope somebody has an suggestion for me. I tried to use the TOUGH3 exe, but the simulation always stops in between and its not running up to…
-
bounds with different temperatures
Hi, I'm new using TOUGH 3 I would like to know how to define a model in EOS1 with two bounds with different temperature each.
-
INSTALL OF TOUGH2
I purchased Tough2 software and i want to run it using PC 64, 8 proccesor, but i couldnot, please can any one you help me in running the software and to run an example,…
-
running MeshMaker file that includes atmosphere and soil
Hello all, I use MeshMaker to create the MESH file. My model includes atmosphere and soil and therefore I put the reference on the ground. I copy the input file that I run with MeshMaker.…
-
Flow of mineral water
Hello, I am studying the chemical effect of water in contact with cement, so I have, basically, several cells made of cement next to others of water. I would like to have a continual reviewal of the…
-
Flow vs Time data from output
Hello everyone! I am a relatively new user of TOUGH3 software. I am using the software to model methane gas migration through soils. I wanted to get the FLOW data of NCG with respect to time.…
-
TOUGHREACT using MINC MESH
I'm running a model about reactive transport in a fractured reservoir. I used MINC function to create the fracture system. However, I have to use 8 characters for the eleme names for the uniqueness…
-
iTOUGH2 ignoring initial successful step
I'm having an issue with an inversion of a TOUGHREACT simulation using the PEST protocol. During each iTOUGH2 iteration, the initial step reduces the objective function but is still labeled as…
-
Non-convergence when upper boundary saturated in CO2
Hi everyone, I am using the module ECO2N_V2.0 to model the hydrothermal fluid and heat circulation into high-topographic volcanoes. I want to create a vadose zone in the upper part of my mesh.…
-
RELP as a function of a VOC mole fraction
Hi everyone, I would like to make the relative permeability of the gas phase a function of the mole fraction of the the first VOC. Actually, the first VOC, in this case,…
-
Limitation to the number of VOCs ?
Hi everyone, I am currently running simulations with 8 VOCs (plus air and water) and I want to add 6 more VOCs. I modified the T2 file like so: - MNEQ = 17 (16 components + one energy balance…
-
Reproducing the carbonate acidizing simulation
Hello everyone, I’m a beginner at TOUGH REACT. I want to reproduce the carbonate acidizing simulation of the paper . but, my simulation results is a slight decrease in porosity,…
-
CO2TAB file in ECO2N
Hello to everyone ! ***I apologize for copying the post, but I have published the previous one in the wrong section.*** I would like to model CO2 injection into high temperature and high pressure…
-
CO2TAB in ECO2N
Hello to everyone ! I would like to model CO2 injection into high temperature and high pressure EGS reservoir. I know that by default, ECO2N has limitations on maximum allowed temperature throught…
-
Question about simulation of rainfall
Hi everyone, I'm working with Petrasim, T2VOC module and I have a question regarding simulation of rainfall. I know I should simulate it by source/sink and define injection rate and enthalpy but I…
-
ERROR: STOP ITOUGH2 : Signal 1 recevied.
Hello everyone, i'm a student, and i'm working on changing the primary variable in iTOUGH2, after some changing in file EOSX and T2F.F and IT2MAIN.F , i compile my executable and when i want to test…
-
Model "Air" in TOUGH
Hi all.. Can someone please tell me whether it is possible to model “Air” in TOUGH? Like for instance, I have a (1m) height tank (closed at top) filled with waste (0.8m) which is emitting methane.…
-
Cannot open file /parallel.info
Hi I am trying to use Parallel option for parallel execution but I am getting error that it cannot open /parallel.info in the itough2 output along mkdir: missing operand.…
-
Heat Conductivity and Specific Heat
Regarding the magnitudes of these 2 parameters in the ROCKS section, I have not figured out what they exactly represent. For example, If I have a 30% sandstone,…
-
Beginner
Hello everyone, I just got Petrasim+Tough2 licence from work but I have no idea where to start and how to start. I have noone around to ask and no experience with other simulators either.…
-
Fortran runtime error!!
Hi, I am running a model with EOS7C on UNIX. The code seems working with no convergence error. But, I always get: Fortran runtime error: Expected REAL for item 14 in formatted transfer,…
-
Actually, I need a software I could model the Coupling Thermo-Hydro-Mechanical damage.
I was wondering if this software(TOUGH2) is suit for this purpose or not. please let me know if you have any more information in this area.Thanks
-
Using TMVOC or just TOUGH basic (EOS9) ?
Hi, can i know the step for LNAPL spill on top of surface then migrate to the bottom of soil, I just wanna check the saturation of soil and the velocity of LNAPL in unsaturated soil condition.…
-
mesh creation
I have a question regarding mesh creation. I am working with Petrasim, T2VOC. I appreciate if you could help me. Is there any limitation for creating mesh?…