-
ECO2M:run is not convergent
Dear TOUGH community users, I am using T2WELL/ECO2M to simulate the injection of CO2 into the aquifer, building a model of 0~-900 m (3D) and the aquifer is located in-750m~-800m.…
-
Error when trying to output the time series
So, I have 40000+ elments, and I want to output all of them's data, so I put all the elements in the solute.inp, for example But then I have the error Elements for which to output time series:…
-
The Example in TOUGH2's ECO2N：Radial Flow from a CO2 Injection Well
Dear all, I am using TOUGH2 ECO2N and I have confused about the example in Page 28 of the manual ECO2N: A TOUGH2 Fluid Property Module for Mixtures of Water,…
-
T2WELL and TOGA coupling
Hello, everyone. Recently our group would like to do about CO2 injection into reservoir for CO2 flooding and sequestration based on wellbore-reservoir coupling model.…
-
About the toughreactEco2n v1.2 not have the “savechem”files
Hello everyone, I was using TOUGHREACT V1.2 to run a initial progress of HC field(no thermal field). There were some problems when adding the chemical field,…
-
About the direction of xyz during mesh creation
Hi， When using meshmaker to make xyz type meshes, I had some confusion regarding the designation of these directions: (1) Regarding the DEG setting, is the angle negative clockwise or…
-
modify output flowdata.tect
Dear all, I 'm using EOS1 with TOUGHREACT V4.13omp and I would like to modify the source code to output in the flowdata.tec file the density of the different phases with their specific internal…
-
Asking for some basic training cases for TOUGH2/ECO2N model
Hello everyone, I'm a new learner of TOUGH2 for CCS project. I'm looking for some basic training case except from ECO2N Manual. I wonder if anyone could help me for this.
-
runtime in Problem 6 2-‐D Radial Model for CO2 Sequestration in Deep Saline Formation from TOUGHREACT V4
Hello everyone! I am working on Problem 6 2-‐D Radial Model for CO2 Sequestration in Deep Saline Formation from TOUGHREACT V4.0. I already got the results for the first 10 years...…
-
Temperature strange behavior
Dear TOUGH-community, I am simulating CO2 injection into a saline aquifer using T2Well/ECO2N - the model geometry is attached. Initially, the model is under hydrostatic equilibrium,…
-
Some questions about TOGA
Dear TOUGH community users, I am new to TOGA and I have some doubts about TOGA. (1) Whether mineralization reaction can be added to TOGA, so that I can determine the distribution of mineralized…
-
Stuck on Performing Simulation, and chdump.out stops writing resutls
It shows multi TIME=0 CHEM.ITRERATIONS is 1 for all of them So does this mean it doesn't converge on CHEM? Thanks
-
Describe the GENER block in context of the sample problem p6_eco2n
Could someone kindly provide an explanation of the GENER block, along with a discussion of its defined parameters, focusing on sample problem "p6_eco2n_2D_radial"?
-
Does TMVOCBio in TOUGH3 have any option for 3-phase hysteresis
Hi all, What I recall is that TMVOC did not have Hysteresis options for three-phase capillary pressure and relative permeabilities (see the link). Seems it is still the case in TMVOCbio (in TOUGH3).…
-
issue with standalone MESHMAKER
Hi all, when I use the built-in MESHMAKER in TOUGH, I first write the MESH block in the "flow.inp" file and then, I put the "flow.inp" file in a folder along with the executable file.…
-
Don't understand what causes this error
The first picture is the error from .exe, the second error is in the VERS, and only flow.out has been created flow.out:…
-
Gas production units in TOUGH+ is it m3/d or Sm3/d in Hydrate_Status : T+H v 1.5
I am trying to figure out whether T+H v 1.5 reports Sm3/d in Hydrate status file or simply m3/d. If it is m3/d then how do i get the necessary Thermodynamic variables to change it to Sm3/d.…
-
New to Tough simulator, question about Mesh
Hi, I am new to Tough simulator, and I have built a model in Gmsh, it would be great if anyone tells me what material I should look at to use my model. Thanks!
-
EOS7MG-A new TOUGH3 module for multiple gas mixture simulation
Recently, we have developed a new TOUGH3 EOS modules named ESO7MG. It is designed for modeling water, brine, and multiple gas species and their mixtures including hydrogen in subsurface multiphase…
-
PyTOUGH: trying to visualize interblock fluxes for a MINC mesh with 'write_vtk'
Hello everyone, cc. @adrian_croucher I've been working with MINC meshes with the aid of PyTOUGH, which is quite handy, however, when I want to visualize (interblock) fluxes using the 'write_vtk'…
-
Can TOUGHREACT automatically calculate injection rate into each element?
Hello, I was wondering if TOUGHREACT can automatically calculate the injection rate into each element without the user interfering? For example, I would like to injection 90 kg/s into a layer that is…
-
how to debug Tough3 in vscode
Hi all, When configuring, I changed the -- build type to debug, which can generate an executable file called tough3-eco2n in the tough3-install folder. Then,…
-
Metis and parallel computing in Tough
Hi All, I found many descriptions about Metis in the User's guide of Tough2-MP. However, there is little description of Metis in Tough3. So, is Metis used in Tough3 for parallel computing? Moreover,…
-
Mesh
After write a code for mesh in notepad How do run it
-
MESH cREATION
Hi everyone. I am new here. How does one run a meshmaker simulation, i.e create a mesh from scratch.