-
How to assign pore pressure gradient
Hi, I have a question in assigning the pore pressure gradient in TOUGHREACT? I tried to assign the pore pressure to each zone by the txt file, but failed. Is there anyone has the experience? Thanks.…
-
TOUGHREACT ECO2N, temperatures higher than 110 ˚C
I am using Petrasim 5.3.1203 for a scenario to inject water and 5% CO2 in a deep geothermal reservoir to examine the mineral interactions and their impact on the fluid flow.…
-
Question about Restart in TOUGHREACT
Hello Everybody, I am struggling to get running a restart and I would really much appreciate your insights. I'm using eos1 in toughreact_V2. The first run is a 2d model in which I have 8 minerals,…
-
Rapidly reducing temperature in cells and MINC problem
Hello, I'm trying to recreate the simulation of the Coso EGS as published by Kovac et al on the Stanford Geothermal workshop in 2006. I have two questions that I would be grateful to have some…
-
Database TherAkin10.dat
I need some information about the thermodynamic data from TherAkin10. For example what means k-feldspar k-feldspar-kk or magnesite and magnesite-2 and why is the Log K much greater for magnesite-2
-
In ECO2N, the injected co2 gas is mixed with a certain amount of so2
hello: I would ask how the injected co2 gas in ECO2N contains a certain amount of so2. Is the setting method like me correct. Thank you for the reply. Thank you
-
ECO2N(I would like to ask what figure CO2 means? Why is the mole fraction greater than 1?thanks)
I would like to ask what figure CO2 means? Why is the mole fraction greater than 1?thanks
-
EOS1 non-convergence
Hello! I am a beginner in TOUGHREACT. I ran it based on the input file provided by the author of a paper. However, when I ran toughreactV2.0, I found that the model did not converge and the program…
-
Temperature dependence cation exchange
Hello, I included cation exchange in my simulation, in which I simulate injection of hot (90 degrees C) water into a relatively cold aquifer with the exact same composition.…
-
How to set up well bore
Hi TOUGH community, I am trying to incorporate a well bore into my simulations in TOUGHREACT, and I am confused on how to set up my mesh. Please, kindly Assist.
-
Speciation with brine using Pitzer
I am trying to run a simple speciation problem with a brine composition in contact with some minerals (like Albite, Barite, Illite, K-feldspar etc.). The idea is to use the results of the speciation…
-
how to use RESTART to inherit the minerals fractions and change P T?
Hi, My model is 1D with 10*10*400 meter. Firstly, I renamed the save and savechemical to INCON and inchemical in the first simulation, and copied these two files to the second simulation folder.…
-
TOUGHREACT model boundary grid Settings
Hello, I want to set up flux-free boundary conditions in TOUGHREACT, how do I set up the related mesh?
-
Tough code
Hello, I am a doctoral student at Xi'an Jiaotong University. Due to the regional restrictions, it is unable to buy the ToughReact code, can you share a ToughReact source code? Very grateful
-
time.out won't output the data of the last timestep
So my last timestep is 8.64e3 sec, but the time.out the last data in time.out is Is there any setting? I don't want to go the .tec file to find the cell by XYZ, thanks!
-
Stuck on Performing Simulation, and chdump.out stops writing resutls
It shows multi TIME=0 CHEM.ITRERATIONS is 1 for all of them So does this mean it doesn't converge on CHEM? Thanks
-
Describe the GENER block in context of the sample problem p6_eco2n
Could someone kindly provide an explanation of the GENER block, along with a discussion of its defined parameters, focusing on sample problem "p6_eco2n_2D_radial"?
-
Error with secondary species not found in thermodynamic database
Hello I am trying to run a TOUGHREACT simutlaion and everything is fine up until it reads the thermodynamic database. I get this error: "Error: The defined secondary species:…
-
Is TOUGHREACT only suitable for NaCl salt?
Hello everyone, I am conducting an experiment using different salts and distilled water to prepare brine. I was wondering if I can simulate the experiment using TOUGHREACT as it appears Toughreact…
-
Use input files for injection rates at many timesteps?
Hello, I am trying to include many CO2 and brine injection rates over a range of timesteps in TOUGHREACT. I was wondering if I would be able to call a file with all of the data I want in GENER,…
-
How to confirm mole fractions of injected CO2 and SO2
Hello, I'm new to Toughreact codes. I'm simulating 1-D flow through a rock sample of dimension 50mmx100mm. CO2 is injected with SO2 impurity (10% of CO2 volume fraction) for 24 hours (1 day) and the…
-
changes in chemical.inp
Dear all, I am a totally new Toughreact user so please forgive me if my question is a bit stupid. I want to modify the chemical.inp from one of the Toughreact examples (1d-CO2).…
-
OUTPT section
I use cubes to construct an octahedron prism. The cross-section shape is shown in the attachment. The largest distance in three directions is 41, 41, 291. How do I write the OUTPT section? Thanks!
-
Error in Problem 6 2-‐D Radial Model for CO2 Sequestration in Deep Saline Formation from TOUGHREACT V4
Hi everyone, I have been trying to run TOUGHREACT V4 Deep Salt Formation 2-D Radial Model Problem 6 with the instructions in the manual. however, I have only obtained results for the first 10 years…
-
TOUGHREACT error while loading shared libraries: libifport.so.5:, but used gfortran complied
I was trying to run some test files using treactv413omp_eco2n_linux, but I ran into the error: error while loading shared libraries: libifport.so.5: cannot open shared object file:…