-
question about TOUGH2 output
Hi, dear all I'm working on geothermal model by using TOUGH2 with PetraSim. Now I want to conduct with model calibration by using PEST. To do so, I must output temperature from TOUGH2 model,…
-
Restart problem
Hello, I am running a series of simulations which were running well until the last restart. With the most recent restart, when I wish to restart the program immediately stops and gives this error…
-
Relative permeability curves in tough2
Hello Every one I faced problem with the relative permeability curve while I working with tough2.1 to build a 3D reservor model for CO2 storage by using both the source code and also the petrasim…
-
Accessing gfortran and MPI on PC through the Cygwin environment
One option to get gfortran and MPI on PC is through Cygwin,a unix-like environment for PC. To setup an environment suitable for compiling TOUGH-related codes, please follow the following steps: 1.…
-
Changing boundary condition for chemistry in EOS3, TOUGHREACT
Dear all, I would appreciate it very much any help with the following: In the problem I model I use constant concentration chemical boundary condition,…
-
Tough2-Flac Coupler
Hi, I was wondering if Tough2-Flac couple module is available to public? if yes where can I download it? Thanks, Attila
-
INSTALL OF TOUGH2
I purchased Tough2 software and i want to run it using PC 64, 8 proccesor, but i couldnot, please can any one you help me in running the software and to run an example,…
-
"Default porosity" definition
Hi everyone, Just a quick post to ask a simple question: is the "default porosity" POR in ROCKS the total porosity? For instance, total porosity for clay formations is, in general, about 40-50%.…
-
Time Problem TOUGH2 with EOS7R
Hello everyone, I’m a new TOUGH2 user. I am trying to simulate a diffusive transport of nuclides in porous media. The input works and I get good results.…
-
Atmospheric Boundary Conditions
Hi all, I am confused with the boundary conditions that have to be imposed in an atmospheric boundary element for simulating evaporation with TOUGH2 (or TOUGHREACT). In a few slides (http://esd1.lbl.…
-
TMVOC-MP
Hi, has anyone run TMVOC module with Tough2-MP successfully? Our current project has big area and needs fine mesh in pay zone, plus the MINC natural fractures,…
-
Tough2-MP TMVOC module
Hi, has anyone run TMVOC module with Tough2-MP successfully? Our current project has big area and needs fine mesh in pay zone, plus the MINC natural fractures,…
-
Installing T2 and iT2
Hey everyone, My colleague and I recently purchased T2 and iT2 through our University, however we both kinda suck at installing programs etc ... can anyone help us?!…
-
Tough+Realgasbrine
Hi there, I'm planning to attend the short course of Tough+Realgasbrine in September, is it a new module going to be released? Do you have any idea when will it be available? Thanks.
-
Tough+Realgasbrine
Hi there, I'm planning to attend the short course of Tough+Realgasbrine in September, is it a new module going to be released? Do you have any idea when will it be available? Thanks.
-
EOS1 - REDUCE TIME STEP error
Hello, I am simulating the single-phase radial flow of water to a well during 13 days of pumping test. I am using EOS1 with MULTI (1,2,2.6). After running the code,…
-
Viscosity of a pure VOC - Error in the formula
Hi everyone, A quick post just for you to note that the formula (4.3.12) in the TMVOC user's manual is not correct. It should be written : ln(µ) = A + B/T + C*T + D*T*T instead of ln(µ) = A - B/T +…
-
Injecting Hot Upflow with MINC
I am running a natural state geothermal model and running into the following issue: With a single-porosity model, the upflow condition is hot water injected, about 290 C.…
-
Inversion of tracer test data
In a recent project, I am considering the idea to invert tracer test data (concentrations) obtained in a producer well, in order to get saturations of two-phase flow,…
-
Anisotropy in Gslib
Hi, I'm using iTough2 and am trying to create a heterogeneous field using gslib. I could not actualy figure it out what is the definition of the ang2 and how to define the anisotropy ratios.…
-
Axis rotation
Hi everyone. I want to rotate my axis from y to z. Now I have an input file where my domain is in x-y (constant width as z direction), but gravity is in z direction.…
-
Is pore compressibility in TOUGH2 not identical to bulk compressibility(1/K)?
Hello. Recently, I am trying to solve 1-D consolidation problem(Terzaghi's) with TOUGH-FLAC. In order to solve it, I first run FLAC to consider pore pressure generation(Skempton's effect).…
-
Convert TOUGHREACT output to Tecplot readable output
Has someone generated a utility to convert TOUGHREACT output files into files that are readable by TECPLOT? I found the EXT utility for converting TOUGH2 output into TECPLOT-formatted files,…
-
Define oil and water production rate for cells
We are using EOS8 modulus to simulate a reservoir with oil and water 2 phases. For the production well, there are oil and water production. How do we define the oil and water rate for the…
-
How can I add a free-flow Neumann boundary condition to a boundary?
I understand that IFD framework has no-flow BC by default. I am trying to set up a 3D problem where all the boundaries except the top have no-flow BCs.…