-
Tough2-MP TMVOC module
Hi, has anyone run TMVOC module with Tough2-MP successfully? Our current project has big area and needs fine mesh in pay zone, plus the MINC natural fractures,…
-
Installing T2 and iT2
Hey everyone, My colleague and I recently purchased T2 and iT2 through our University, however we both kinda suck at installing programs etc ... can anyone help us?!…
-
Tough+Realgasbrine
Hi there, I'm planning to attend the short course of Tough+Realgasbrine in September, is it a new module going to be released? Do you have any idea when will it be available? Thanks.
-
Tough+Realgasbrine
Hi there, I'm planning to attend the short course of Tough+Realgasbrine in September, is it a new module going to be released? Do you have any idea when will it be available? Thanks.
-
Viscosity of a pure VOC - Error in the formula
Hi everyone, A quick post just for you to note that the formula (4.3.12) in the TMVOC user's manual is not correct. It should be written : ln(µ) = A + B/T + C*T + D*T*T instead of ln(µ) = A - B/T +…
-
Injecting Hot Upflow with MINC
I am running a natural state geothermal model and running into the following issue: With a single-porosity model, the upflow condition is hot water injected, about 290 C.…
-
Inversion of tracer test data
In a recent project, I am considering the idea to invert tracer test data (concentrations) obtained in a producer well, in order to get saturations of two-phase flow,…
-
Anisotropy in Gslib
Hi, I'm using iTough2 and am trying to create a heterogeneous field using gslib. I could not actualy figure it out what is the definition of the ang2 and how to define the anisotropy ratios.…
-
Axis rotation
Hi everyone. I want to rotate my axis from y to z. Now I have an input file where my domain is in x-y (constant width as z direction), but gravity is in z direction.…
-
How to assign a permeability for each grid cell?
Hi. I am trying to convert an Eclipse simulation model to TOUGH2. In the Eclipse model each grid cell has a (diagonal) permeability tensor, with a scalar for permx, permy, and permz.…
-
Convert TOUGHREACT output to Tecplot readable output
Has someone generated a utility to convert TOUGHREACT output files into files that are readable by TECPLOT? I found the EXT utility for converting TOUGH2 output into TECPLOT-formatted files,…
-
Define oil and water production rate for cells
We are using EOS8 modulus to simulate a reservoir with oil and water 2 phases. For the production well, there are oil and water production. How do we define the oil and water rate for the…
-
lacking of continuous column of CO2 from the injection point to the caprock in a sandstone reservoir model
Hi, I am injecting CO2 in a high porosity and permeability sandstone reservoir during a period of 30 years. It is an isothermal model. I have a problem with the CO2 plume.…
-
Steam Liquid coexistence
Hi, I’m a new Petrasim user and I would like to make some questions: I tried to build some geothermal model s and I have watched some tutorials and I’ve read some publications.…
-
MINC problems in post processing
Hi, everyone. I`m studying dual permeability problem and I`ve got a dual permeability modeling result. Anyway I`ve ran into difficulties doing post processing after running.…
-
MINC and low permeability case problem in Tough2
Hi All, I set up a case using the MINC with 2 continua. The first continua represents the fracture and the second one represents the matrix. For this case,…
-
Do you have a recommended module to simulation gas condensate reservoir?
It's a deep gas condensate reservoir, what's module is good for it? What about EOS7C? Thank you very much
-
Hi everybody, I have a question regarding a particular simulation (I am using Petrasim). Can you help me?
Hi everybody, I have a question regarding a particular simulation (I am using Petrasim). Can you help me? I am trying to simulate the heat and fluid flow within a volcanic edifice.…
-
T2VOC for simulating Air Sparging under changing injection rates.
Hi, I would like to use T2VOC to model air sparging in saturated soil, to simulate the effect of change in injection rate on two things: (1) ROI (radii of influence);…
-
Help with defining basic Confined and Unconfined Aquifer and transport models
Hello All, I am brand new to PetraSim and have been trying to learn to make basic models of confined and unconfined aquifers, model advection-dispersion,…
-
TOUGH2 and TOUGHReact Compatible MacOS
Hello, I am using both T2 and TReact on my Mac using OS X Mavericks 10.9.5. Are either compatible with the new Yosemite OS? I had downloaded it and wanted to install but do not want to have to…
-
Error on installation
I'm trying to install TOUGH2 for EOS2 and I'm having trouble in the compilation. I'm not sure if the code is right and when I type it, I receive this message.…
-
Oil relative permeability in EOS8
Hi All, I am trying to set up the input file for EOS8 module to run a water flooding oil case. As from the manual, the oil relative permeability is set to be linear with respective to oil saturation…
-
A problem with my simulation with EOS9nT
I have some problems in my modelling project with EOS9nT. In my example I want to simulate the nuclide release and transport process in a disposal site with a 3-D model.…
-
TEXPOM - exponent for calculation of chemical diffusivity
Hi everyone, I am currently adding properties of the chemical Hexachlorobutadiene into the CHEMP block. There is the TEXPOM data missing as I do not know where to find the definition in the TMVOC…