-
TOUGHREACT ECO2N
Hi, I'm quite new in using TOUGHREACT. Can anyone please clarify one question I've been having for quite a while now? The system I'm trying to model is just simple mixing between brine defined by the…
-
STIMAX parameter: Which ionic strength is considered?
Dear all, I have a question concerning the STIMAX parameter in the solute.inp file in record 3. As described in the TOUGHREACT V3.0 manual, STIMAX acts as:…
-
Is there a limitation in the number of grid blocks to be printed out?
Hi- I ran two simulations with different number of grid blocks to be printed out in 'time.out' The first case with 10 grid blocks had no problem at all but the other one with 100 blocks encountered…
-
EOS7C tracer phase
Hi All, In EOS7C, what phase is the tracer in at injection? I have defined a Henry's constant, but presumably that takes effect after injection. Also, how can I see output for tracer in the liquid…
-
Mass Balance for trace gases in TOUGHREACT V3-OMP
Dear colleagues, I stumbled about a little problem concerning the mass balance for trace gases using the new TOUGHREACT V3-OMP version. I am simulating the injection of CO2 containing trace gases…
-
(ECO2N)CANNOT FIND PARAMETERS AT ELEMENT * *, for help
Hi,dear all, I'm here agian. I was puzzled by a question for a long time, I appreciate anybody can provide some suggestion. I have attached my input file, MESH,INCON,and the output file,…
-
No show of SAVE and savechem files in restart option
Hi, I am running TOUGHREACT though, I think it's also applicable to TOUGH2 users. I am trying to use restart option, but I can't find those two output files (SAVE,…
-
EOS3 bug?
When I run the input attached I receive the error below. I do not have a number 466560 anywhere in the input file. When I debug the source code, temperature 27.0 becomes 46656000027.…
-
ECO2N, initial condition
Hi,dear all I'm working on gravity equilibration by TOUGH2 ECO2N module. First,the bondary condition is shown in the picture, and I have attached my input file, MESH,SAVE,and the output file.…
-
"EOS CANNOT FIND PARAMETERS AT ELEMENT" error message
Hi, dear all I'm working on geothermal model by using TOUGH2 with PetraSim. Now I had generated input file from PetraSim (0114.dat) and recompile the eos1.exe file.…
-
Oxidation extension
Hi all What are the possible ways to add oxidation extension to TMVOC? Is there any available code like TMVOCbio? Thank you
-
How to handle time step control for proper chemistry computation?
Dear all, I am struggling with some Toughreact basics and maybe some of you can explain me shortly how to handle the time step control in a proper way to avoid mistakes and miscalculations.…
-
Atmosphere boundary thickness
Hi all I am trying to quantify gas emissions into the atmosphere. But the gas diffusion is highly dependant on atmospheric thickness, isn't it? Whats the most reasonable value for this? Stefan,…
-
MGTAB
Hi I am trying to run a domain containing numerous generation sources (>1000). I have faced an error about the number of generation sources. I searched for "MGTAB" in source codes and I found in…
-
MINC
Hi For modeling the topsoil cracks using MINC, what should be the number of continua? I think that two is fine, but is it? How can I apply the fracture to a certain number of cells?…
-
TOUGH2-MP
Hello everybody, so I've successfully compiled TOUGH2-MP and decided to test it in the r1dv example files. I always get a segmentation fault error. Specifically I get the following message: [terra:…
-
Error message help
Hi Everyone, I am not sure I ask this question in the right forum. I am testing the Tough3 EOS1 with Minc. The cell number is about 0.4 million including the MINC element.…
-
TOUGH2-MP compilation error
Hello everybody, My research centre has a version of TOUGH2-MP and we are trying to install it with ECO2N eos in the cluster: Cluster: Rocks Cluster Operating System: Cent OS -> (2.6.32-220.13.1.el6.…
-
EOS7C-running problem
Hi everyone, I am doing a simulation with EOS7C in the heterogeneous coal seam aquifer with water and gas extraction from the well located in the middle of the model.…
-
restart with surface complexation
Hello, I have been trying to run a restart with surface complexation. First, I get an error like that: "Restart time in INCHEM file is not the same as starting time for flow calculations. timetot= 3.…
-
EOS7C pressure range
Hi there, I read through both the tough2 and EOS7C manuals to find the pressure range limitation to run simulations, but I didn't find it. I have a abnormal high pressure reservoir,…
-
Cauchy/Type III Boundary Condition
Hello, Is it possible to apply a head dependent boundary condition, where flux is a function of head difference between a cell and some prescribed value?…
-
Atmospheric Boundary Conditions
Hi all, I am confused with the boundary conditions that have to be imposed in an atmospheric boundary element for simulating evaporation with TOUGH2 (or TOUGHREACT). In a few slides (http://esd1.lbl.…
-
Capillary Pressure Definition
In TMVOC, is the capillary pressure between two phases i and j: Pc_ij = Pi - Pj or Pc_ij = Pj - Pi ? where Pi and Pj are the pressures in the phases i and j. Thank you in advance, Quentin
-
TOUGH 2 ECO2M temperature condition
Hi, It is described in the ECO2M user guide that TOUGH2 simulates CO2 migration under temperature condition up to 110 °C. I am wondering if the temperature condition is about 115 °C-125 °C,…