kenny (a)'s Profile - TOUGH User Community

Skip to main content

Latest Posts

Re: error compiling TOUGH3 on Ubuntu : Failed to build TOUGH TPLS
@Haiyan Zhou The error message 'cannot find -lpetsc' means compiled PETSC library can not be found. It is still the PETSC installation problem. Do you have the source code license of TOUGH3? If yes,…
- kenny
- 3 yrs ago
- TOUGH3
- Reported - view
Re: error compiling TOUGH3 on Ubuntu : Failed to build TOUGH TPLS
Have you try this one: https://tough.forumbee.com/t/g9h57pf/tough3-installation-issue?
- kenny
- 3 yrs ago
- TOUGH3
- Reported - view
Re: CO2 injection in a depleted oil field
What components are you considering for the simulation? For CO2, salt, water, use eco2n, eco2m or eco2n V2. for CO2, CH4, Oil, water, try TOGA
- kenny
- 3 yrs ago
- TOUGHREACT
- Reported - view
Re: TOUGH2-MP : simulations halted after 1 day simulations
You did not specify the linear solver in the input file. The program picks up AZTEC for solving linear equations, but it does not work properly for your model.…
- kenny
- 3 yrs ago
- Questions & Answers
- Reported - view
Re: How to set a production well with constant pressure
For the constant pressure well, you may use a virtual large volume (1.0e50) element connected to the well block, the flux between the virtual block and the actual well block is the injection and…
- kenny
- 3 yrs ago
- TOUGH+
- Reported - view
Re: Error compiling TOUGH3
@Barbara Carrera I can not duplicate the problem on my computer. AZTEC requires less effort for compilation. I did not separate it from the TOUGH3. We are preparing a minor updated version of TOUGH3…
- kenny
- 3 yrs ago
- TOUGH3
- Reported - view
Re: Volume and Mass Balance Error in flow.out
Do not have enough information to figure out the reason, but I do see you have MULTI (2 2 3 6). EWASG does not use (2 2 3 6)
- kenny
- 3 yrs ago
- TOUGHREACT
- Reported - view
Re: TOUGH2-MP : simulations halted after 1 day simulations
The bug for AZTEC has been fixed long time ago. You seems have different problem (The AZTEC bug problem halts at the first time step, but your model runs to time step 155).…
- kenny
- 3 yrs ago
- Questions & Answers
- Reported - view
Re: Volume and Mass Balance Error in flow.out
Do you have a mesh file? Everything being 0 could be caused by the gridblocks volume=0 or porosity=0. You may check.
- kenny
- 3 yrs ago
- TOUGHREACT
- Reported - view
Re: SAVE file not consistent with OUTPUT
Can you post the input and outputs? I am interested in investigating the reason for this problem.
- kenny
- 3 yrs ago
- TOUGH3
- Reported - view
Re: A question about coupling TOUGH2 and FLAC3D
This seems a question for 'FLAC3D', not for TOUGH
- kenny
- 3 yrs ago
- Questions & Answers
- Reported - view
Re: End time of simulation
I guess you limit to the simulation with a maximum number of 999 time steps. After 999 time steps, the simulation only reaches around 300 years. If you need longer time simulation,…
- kenny
- 3 yrs ago
- TOUGH3
- Reported - view
Re: End time of simulation
can you post your output file here? There is no enough information to tell the reason.
- kenny
- 3 yrs ago
- TOUGH3
- Reported - view
Re: TOUGHREACT_Debugging
I am pretty sure something wrong with flow.inp formatting. Please try entering 2 empty lines before keyword RPCAP.
- kenny
- 3 yrs ago
- TOUGHREACT
- Reported - view
Re: Getting Started: Homogenous Aquifer
See the corresponding keywords in user manual section 8, such "ROCKS' section for information of Rocks.
- kenny
- 3 yrs ago
- TOUGH3
- Reported - view
Re: Assigning source/sink in GENER block without element name/ using meshmaker
(1) Then format is wrong for SS_GROUP namelist input. You may take a look of the source code, to make sure the correct format requirement (it changes sometime).…
- kenny
- 3 yrs ago
- TOUGH+
- Reported - view
Re: TOUGH + Phase equilibrium Relationship...where am i wrong?
Have you compared your equilibrium pressure plot with the the figure presented in the T+H user manual? I guess something wrong with your calculation for the equilibrium pressure.
- kenny
- 3 yrs ago
- TOUGH+
- Reported - view
Re: Getting Started: Homogenous Aquifer
TOUGH always uses SI units. TC at here is the formation heat conductivity under fully liquid-saturated conditions and has a unit of W/m˚C.
- kenny
- 3 yrs ago
- TOUGH3
- Reported - view
Re: Error compiling TOUGH3
@Barbara Carrera Yes, you can compile TOUGH without repeat compiling PETSC again. Please have a look a look of following post for a solution: https://tough.forumbee.…
- kenny
- 3 yrs ago
- 1
- TOUGH3
- Reported - view
Re: Meaning of this error ?
You may use a virtual large volume (vol=1.0e50) connecting to the well gridblock. The virtual element has a pressure equals to the production pressure (depressurization, may change with time) .…
- kenny
- 3 yrs ago
- TOUGH+
- Reported - view
Re: Meaning of this error ?
Do you mean using a large-volume virtual gridblock as a depressurization element for production? As both water and gas will be produced, I would suggest using AqG.
- kenny
- 3 yrs ago
- TOUGH+
- Reported - view
Re: Meaning of this error ?
You gave an initial pressure 1.21189961E+07 with a Hydrate-Aqueous (AQH) condition at the element " 541 ", but the given pressure is less than equilibrium pressure ( 1.…
- kenny
- 3 yrs ago
- 1
- TOUGH+
- Reported - view
Re: Assigning source/sink in GENER block without element name/ using meshmaker
It seems something wrong with reading input file please try: MM.exe <Stencil_3DCart >Stencil_3DCart.out
- kenny
- 3 yrs ago
- TOUGH+
- Reported - view
Re: Assigning source/sink in GENER block without element name/ using meshmaker
The mesh file generated by meshmaker should include the coordinates of each element of the mesh. Based the coordinates of well, you can find an element located at the same location as the well and…
- kenny
- 3 yrs ago
- TOUGH+
- Reported - view
Re: Controlling BHP in TOUGH3's INFILE
If it is a production well, you may use DELV well type to keep the bottom hole pressure constant. You can also use a virtual huge volume gridblock connected to well for injection or production (the…
- kenny
- 3 yrs ago
- TOUGH3
- Reported - view

1 5 6 7 8 9 10 11

Back to top

Home

View all topics

TOUGH Website