TOUGH Website

How to enable Javascript

Latest Posts

Re: Instant release EOS7R @Curt Oldenburg Thank you very much Curt, That was the question! Barbara
- BARBARA FERRUCCI
- BARBARA_FERRUCCI
- 5 yrs ago
- TOUGH2
- Reported - view
Re: Instant release EOS7R Hello Yingqi, If I well understood, the release rate in GENER block constitues a flow-through conditions (kg/s), but using the INCON block it constitues an instant release expressed in mass fraction.…
- BARBARA FERRUCCI
- BARBARA_FERRUCCI
- 5 yrs ago
- TOUGH2
- Reported - view
0
Instant release EOS7R
Hello everybody, To simulate an instant release of a radionuclide in eos7r, we have to insert a no-zero value of the component in the INCON block. This value should be the mass fraction of the…
- BARBARA FERRUCCI
- BARBARA_FERRUCCI
- 5 yrs ago
- 4 replies
- 336
- TOUGH2
0
Restart option with PetraSim
Hello everybody, There is a procedure for the restart of a though2 run. I interrupted a run of Tough2, I can restart it where it left off? Thanks
- BARBARA FERRUCCI
- BARBARA_FERRUCCI
- 6 yrs ago
- 317
- TOUGH2
Re: Permeability Modification option EOS7R Thank you very much Stefan!
- BARBARA FERRUCCI
- BARBARA_FERRUCCI
- 6 yrs ago
- TOUGH2
- Reported - view
Re: Permeability Modification option EOS7R Hi Stefan, Thank you for your answer. I'd like to ask you if I have been understood correctly, because the user's giude is not clear. If the absolute permeability of the rock is 1e-18 and I want…
- BARBARA FERRUCCI
- BARBARA_FERRUCCI
- 6 yrs ago
- TOUGH2
- Reported - view
0
Permeability Modification option EOS7R
Hello everyone, Please, does anyone know if the permeability modification option may be used in EOS7R?
- BARBARA FERRUCCI
- BARBARA_FERRUCCI
- 6 yrs ago
- 4 replies
- 531
- TOUGH2
0
To have "Component mass in place" in a single cell
Hello everyone , In the output file of TOUGH2, for each plot time value, there is the -component mass in place- table, in which I think, are reported the mass of each component referred to the total…
- BARBARA FERRUCCI
- BARBARA_FERRUCCI
- 6 yrs ago
- 314
- TOUGH2
Re: Zero flux conditions Thank you Stefan, Now I understand my mistakes. But I have a doubt concerning the use of the inactive cells. I have seen the EOS7R Sample Problem of TOUGH Short Course.…
- BARBARA FERRUCCI
- BARBARA_FERRUCCI
- 6 yrs ago
- TOUGH2
- Reported - view
0
Zero flux conditions
Hello everyone , Could someone explain to me how to impose the zero flux conditions in a generic domain? Thank you.
- BARBARA FERRUCCI
- BARBARA_FERRUCCI
- 6 yrs ago
- 3 replies
- 679
- TOUGH2
Re: How to assign the material properties to mesh (ELEM block) Ok. I found the solution to my problem. I have to use AssignRock program.
- BARBARA FERRUCCI
- BARBARA_FERRUCCI
- 7 yrs ago
- TOUGH2
- Reported - view
0
How to assign the material properties to mesh (ELEM block)
Hi everyone, I need to assign the material properties to mesh elements into the ELEME block. In the EOS7R sample there is the MESH_MatNum file in which the material properties are already been…
- BARBARA FERRUCCI
- BARBARA_FERRUCCI
- 7 yrs ago
- 1 reply
- 578
- TOUGH2
0
Problem with RF1 input file
Hello everyone, I'm starting to use TOUGH2 for the first time. I tried to run the sample-input file RF1, but the output file gives me an error and I don't know how to proceed.…
- BARBARA FERRUCCI
- BARBARA_FERRUCCI
- 7 yrs ago
- 388
- TOUGH2
Re: INSTALL OF TOUGH2 Hello Everyone, I followed the instructions above in order to obtain the T2CG2 excutable file. I am using gfortran in Cygwin, but it give me these errors:…
- BARBARA FERRUCCI
- BARBARA_FERRUCCI
- 7 yrs ago
- TOUGH2
- Reported - view
Re: Starting with TOUGH2v2 Thank you. I Hope to make it. Barbara
- BARBARA FERRUCCI
- BARBARA_FERRUCCI
- 7 yrs ago
- TOUGH2
- Reported - view
0
Starting with TOUGH2v2
Hello everyone, I have TOUGH2 distributed by NEA. I recieved a DVD containing TOUGH2 source code, all of the EOS modules with '.F ' extension, and some input data for the sample problems.…
- BARBARA FERRUCCI
- BARBARA_FERRUCCI
- 7 yrs ago
- 2 replies
- 717
- TOUGH2
Re: Time Problem TOUGH2 with EOS7R Hi Maike, Also I am a new TOUH2 user. You solved your problem ? I think it's because the convergence is achieved on the first iteration and the steady state has been reached.…
- BARBARA FERRUCCI
- BARBARA_FERRUCCI
- 7 yrs ago
- TOUGH2
- Reported - view

Back to top

BARBARA FERRUCCI

BARBARA_FERRUCCI

17
0
0

Follow