TOUGH Website

How to enable Javascript

Latest Posts

0
compiling T2Well-ECO2N v1.02 instructions
Hi all, I have a mesh that exceeds the maximum number of connections (MNCON = 57,000 set as the default for TOUGH2). Having looked across the forum I can see that the T2 source code file can be…
- Hannah Doran
- Hannah_Doran
- 5 mths ago
- 6 replies
- 63
- TOUGH2
Re: applying heat load in BHE and varying input T? Thank you both for your replies, I have been having a play and have managed to obtain the correct T down the wellbore when I inject 0.58 kg/s and impose an inlet initial T = 11 degrees within INCON.…
- Hannah Doran
- Hannah_Doran
- 7 mths ago
- TOUGH2
- Reported - view
0
applying heat load in BHE and varying input T?
Hi all, I am using T2Well with TOUGH2 to model a borehole heat exchanger and was wondering if it was possible to apply a heat load to the BHE? I have tried something of the form below:…
- Hannah Doran
- Hannah_Doran
- 7 mths ago
- 4 replies
- 33
- TOUGH2
Re: T2Well semi-analytical solution in reservoir Dear Kenny and Yingqi, Thank you both for your fast replies! Kind regards, Hannah
- Hannah Doran
- Hannah_Doran
- 10 mths ago
- TOUGH2
- Reported - view
0
T2Well semi-analytical solution in reservoir
Hi all, I notice in the T2Well manual that you can turn on a semi-analytical solution of the reservoir by setting thermal conductivity in well cells to a negative value.…
- Hannah Doran
- Hannah_Doran
- 10 mths ago
- 3 replies
- 40
- TOUGH2
Re: creating T2Well .exe from source code Hi Yingqi, Thanks for your reply. I have been using the research code T2Well/EOS1 developed by Lehua Pan for borehole heat exchanger designs, but my supervisor gained two licenses for T2Well and…
- Hannah Doran
- Hannah_Doran
- 1 yr ago
- TOUGH3
- Reported - view
creating T2Well .exe from source code
Hi, I have access to a T2Well and TOUGH3 license and would like to have a go at generating the executable from the T2Well source code. I can see in the T2Well/ECO2N manual that there is an NMAKE…
- Hannah Doran
- Hannah_Doran
- 1 yr ago
- 2 replies
- 61
- TOUGH3
Re: T2Well constant fluid properties and EOS1 relationship? Hi Alfredo, Apologies in the delay to my reply. Thank you so much for your comments! I now have a better understanding on the ROCK properties dependent on the EOS after doing the recommended tests.…
- Hannah Doran
- Hannah_Doran
- 1 yr ago
- 1
- TOUGH2
- Reported - view
Re: T2Well constant fluid properties and EOS1 relationship? @Alfredo Battistelli Thank you so much! I wanted to ask another question if that's okay. Can I set a time dependent surface backpressure as opposed to having 1 fixed pressure in PARAM? For instance,…
- Hannah Doran
- Hannah_Doran
- 1 yr ago
- TOUGH2
- Reported - view
Re: T2Well constant fluid properties and EOS1 relationship? @Alfredo Battistelli Thank you very much for your reply! The manual states all parameters in ROCKS are the same as how TOUGH2 defines them apart from the first permeability value PER(1),…
- Hannah Doran
- Hannah_Doran
- 1 yr ago
- 1
- TOUGH2
- Reported - view
1
T2Well constant fluid properties and EOS1 relationship?
Hi, I am currently modelling a wellbore with constant density, thermal conductivity and specific heat capacity thermophysical properties at surface temperature 40 degrees like so: Wella 2 1665.e00 1.…
- Hannah Doran
- Hannah_Doran
- 1 yr ago
- 7 replies
- 77
- 1
- TOUGH2
Re: T2Well in TOUGH3? Thanks for your reply Yingqi, No you answered my question fine. The T2Well research code I used produced results for this open access paper: https://geothermal-energy-journal.springeropen.…
- Hannah Doran
- Hannah_Doran
- 1 yr ago
- TOUGH3
- Reported - view
T2Well in TOUGH3?
Hi, I was just wondering if TOUGH3 can be run with T2Well? I have previously modelled boreholes with two feed zones (inlet and outlet) in the T2Well/EOS1 research code modified by Dr Lehua Pan which…
- Hannah Doran
- Hannah_Doran
- 1 yr ago
- 3 replies
- 92
- TOUGH3

Back to top

Hannah Doran

Hannah_Doran

13
3
0

Follow