-
Error in EXT.exe
Dear team, I encountered an error when using the EXT.exe. I have completed the simulation by Petrasim. But, the CMD indicated that ' forrt1: severe (161) : Program Exception - array bounds exceeded'.…
-
representing an oven using extra cell
Hi everyone, I’m trying to use TOUGH2 to history match a column test where some soil was put inside a glass column and sealed and then put the column itself inside an oven set at some elevated…
-
TOUGH3 + PEST?
Hi all, Can I couple TOUGH3 with PEST (iTOUGH2 code) for parameter optimization? Thanks in advance. Manuel
-
compiling Gslib in cluster
Dear Stefan, I am trying to compile EOS7C-Gslib. It works well on my PC where I used Visual studio. But I can't manage to do the same thing on cluster. I got this linking error: it2main.…
-
TOUGH-HYDRATE - Problems with the maximum mass fraction of methane in aqueous phase
I'm trying to equilibrate a sloping system, containing a AqH phase and a Aqu phase. If methane mass fractions of methane in water are not maximum, hydrate phase dissolves.…
-
ECO2N Steady state
Hi everybody! I'm a new Tough2 ECO2N user and i'm experiencing some problems by reaching the steady state condition... I will use it as Initial conditions for the simulations.…
-
MINC problems in post processing
Hi, everyone. I`m studying dual permeability problem and I`ve got a dual permeability modeling result. Anyway I`ve ran into difficulties doing post processing after running.…
-
Need help on using Ext.exe to generate Tecplot input file
Hello everyone and Stefan, I tried to use Ext.exe to generate Tecplot input files, but it can not work by following the steps in the manual. Attached is my model output and mesh files.…
-
Mesh is truncated-Meshmaker v 1.5
Hello everyone. I am trying to create a mesh, R=200m and Z = -190m. It has multiple layers. I have added all the info and the file runs, but the mesh is created only up to a depth of -94m and no more.…
-
Eorror Compling TOUGH3 with PETSC in WSL
I have installed fortran compliers (gcc, gfortran, g++ (version9.5)) and configured petsc according to kenny's instruction (https://tough.forumbee.com/t/g9h57pf/tough3-installation-issue).…
-
SMCO2 is not increased
Hello I am using Toughreact v3 for simulation for CO2 injection and our simulation runs well, however, CO2 is not mineralized after the simulation has finished.…
-
EOS3-sink/source rates are piecewise constant, how to set up?
As mentioned in the title, I want to set the piecewise constant sink/source rate as shown in the attached figure, but I can't achieve the desired result after setting it many times in petrasim,…
-
Using TOUGH ECO2N for Core flooding
Hi all, I am curious to know if TOUGH2 is able to model a core flooding. Suppose that there is a core sample of length 30 CM. I have tried, however my simulation didn't converge.…
-
TOUGHREACT compilation using gfortran MinGW-error message
Dear Community, I would like to compile TOUGHREACT (version: TR-OMP_Source_v3.3.2-OMP) using gfortran with MinGW. I typed make eos1 -f makefile_gf, and had the attached error message.…
-
How to identify the cause of an incomplete simulation run
Dears, I have a problem to identify the cause of the incomplete simulation run for the attached input file. The simulation ends before the specified total simulation time without error messages!…
-
Not to achineve the end time and no error
Hello everyone, I am trying to run a geothermal reservoir model with EOS1 to predict a production rate for 10 years and the calculation did not achieve the setting end time.…
-
How to consider the evaporation effect of water affected by temperature in tough2
How to consider the evaporation effect of water affected by temperature in tough2 (or what is the governing equation of water conversion in liquid and vapor)?…
-
TOUGH Tips & Tricks
A Faster Way to Make You a TOUGH Expert The following is a collection of TOUGH Tips and Tricks that may help you solve TOUGH problems. To post your own TTT,…
-
TEMPERATURE = 0.000000E+00 OUT OF RANGE IN SAT
Hi All, I am a newbie to the TOUGH simulator and trying to create a small model for brine injection using EOS7 module. While I am trying to run the model,…
-
TOUGH2; grids; running time too long
Hi! I used TOUGH2 for a transient fluid flow analysis (total time for 1 year) using grids showed in the figure. Element volumes range from 1.0e-04 to 2.0e-1.…
-
Problem with running a sample case using TOUGH3/ECO2N
I have started to use TOUGH3 recently for my research. I am trying to model the temperature perturbation during CO2 injection into saline aquifers using TOUGH3/ECO2N.…
-
non-convergence issue
Hi everyone, I'm running a 2d radial case in petrasim where I'm heating from the top, bottom and one side. I first tried to define an extra cell and connect all those boundary cells to it and then…
-
Problem initializing water table at a given elevation in eos9
Hello, In the TOUGH2 manual, it says that an eos9 (Richard's Equation) model can be initialized with a specified water table elevation by setting CWET in REFCO to that elevation.…
-
Compiling TOUGH3 on Linux platform (Ubuntu)
Hi everyone, First of all, I wish a happy new year! Secondly, I have trouble compiling TOUGH3 on an Ubuntu platform and I am wondering where I could find instructions for compiling TOUGH3 on Ubuntu.…
-
"ERRONEOUS DATA INITIALIZATION" on IBM-AIX cluster
I encountered a problem with "ERRONEOUS DATA INITIALIZATION" , when I tried to run serval tests using TOUGH2-MP on IBM-AIX cluster. These tests had been successfully tested using the usual Tough2.…