-
Maximum point for time-dependent injection
Dear all, I am trying to prescribe more points for cyclic injection scenario. I checked the TOUGH2 manual, which indicated to use LTAB for the number of points in the table of rate vs time.…
-
where to specify the tolerance of gas transport in tr2.0
Hi: from a recent simulation, 'runlog.dat' shows the bellow error message: Warning: chemistry did not converge at node a 8 (routine NEWTONEQ), Non-convergence type: absolute Node temperature (C): 10.…
-
Hysteretic RELP and CAP
Hi, Just a quick question: Is it possible to use IPR 12 with ICP 9 ? Following the manual, it should only be implemented with ICP 12, since ICP 12 uses some parameters from IPR 12,…
-
Eorror Compling TOUGH3 with PETSC in WSL
I have installed fortran compliers (gcc, gfortran, g++ (version9.5)) and configured petsc according to kenny's instruction (https://tough.forumbee.com/t/g9h57pf/tough3-installation-issue).…
-
I want to install TOUGH3
Hello, I am a student planning to analyze rock minerals. I would like to install TOUGH3 for the analysis. Please how do I get the software? Thanks. Efenwengbe Nicholas Aminaho
-
TOUGHREACT error while loading shared libraries: libifport.so.5:, but used gfortran complied
I was trying to run some test files using treactv413omp_eco2n_linux, but I ran into the error: error while loading shared libraries: libifport.so.5: cannot open shared object file:…
-
INITIALIZATION ERROR
Hello All, @Kenny or anyone pls find attached my input file for tough+, i just finish inserting all my parameters from the MEMORY block using equilibrium with inhibitor,…
-
Issue modeling a soil with zone of unsaturated vapor
Hi, I am using EOS3 to model a evaporating soil and have encountered some behavior with soil air relative humidity that I think is unrealistic. My 1D setup has a static block at the bottom to act as…
-
T2Well semi-analytical solution in reservoir
Hi all, I notice in the T2Well manual that you can turn on a semi-analytical solution of the reservoir by setting thermal conductivity in well cells to a negative value.…
-
T2well output files
Hello T2well users; I have just started using the code. I run a case with only a well model (reservoir represented solely by the last grid block at the bottom).…
-
Parallel processing for EOS7
I am running T3 on Ubuntu. I have successfully ran ECO2M on multiple cores in the past on this server. However, when running EOS7 on the same server, it compiles normally,…
-
Stopping in main due to flow nonconvergence
Hello everyone, I am using ECO2N to simulate CO2 injection into a formation with relatively low permeability. I am having trouble with an error popping up.…
-
tecplot see my output files for loading
How can the plot_data_element file and other be loaded into tecplot pls?
-
Set An Initial Temperature Greater Than 100 In ECO2N Module
Dear all members, Hi, I am a new TOUGH user and I know that by default, ECO2N has limitations on maximum allowed temperature (103.04 deg. C). But in my case the temperature is 120 deg.…
-
Beginner
Hello everyone, I just got Petrasim+Tough2 licence from work but I have no idea where to start and how to start. I have noone around to ask and no experience with other simulators either.…
-
Seeking help to solve ECO2M problems
Dear TOUGH community users, I have been struggling with the problem of not being able to successfully simulate running T2Well-ECO2M for too long and would like to seek help.…
-
How to change the volume in ELEME Block
I am fairly new to TOUGH -Hydrate and just simulating through the default files available. I would like to know how to or where to add the volume of the reservoir in ELEME Data Block and will have…
-
Reproducing the carbonate acidizing simulation
Hello everyone, I’m a beginner at TOUGH REACT. I want to reproduce the carbonate acidizing simulation of the paper . but, my simulation results is a slight decrease in porosity,…
-
Visualize data using MATLAB - Github link inside
Hello TOUGH/TOUGHREACT community, I would like to share some code I developed on MATLAB to visualize pressure profile, gas saturation, pH, etc. This code only works for 2D data. https://github.…
-
toughio
Dears, I want to read the file SAVE output from tough+hydrate through the toughio library, but the code runs all the time and fails. How can I solve this problem? Thanks in advance
-
Question on modeling water isotopes – after Singleton et al. (2004)
Hi Eric, I have been playing around with your water isotopes model of Singleton et al. (2004) and have a question about how fractionation factors are implemented in TOUGHREACT.…
-
Large runlog.out file
Hi I am having problems with large runlog.out files causing my disk size to get full quickly. I have made sure that the parameters responsible for this in REACT block are not made greater than zero…
-
Technical question regarding mass conservation in TOUGH3
Dears, I am trying to model CO2 injection in brine saturated aquifer using a 1D radial model. CO2 is injected with a constant rate (10 kg/s). Rate distribution throughout the reservoir in my case is…
-
NaN in TOUGHREACT 3 EOS2 simulations
Hello Everyone, I'm using TOUGHREACT 3 with EOS2. When I run the simulation (which runs well in TOUGHREACT 2) the results are NaN in the aqueous concentrations and minerals.…
-
Compiling against more up to date PETSC version
Hi All, Just a question regarding compiling TOUGH3 against a PETSC versions higher than the 3.7 branch. Has anyone tried this? Is it possible? I know at some stage a number of the PETSC function…