-
Is there a possibility to extent the TOUGH2 pressure range?
Hello everyone, I am using TOUGH2 to simulate two phase flow in deep subsurface waste repositories. The pressures in the systems can reach quite high values due to gas production and high…
-
MINC problems in post processing
Hi, everyone. I`m studying dual permeability problem and I`ve got a dual permeability modeling result. Anyway I`ve ran into difficulties doing post processing after running.…
-
udell-fitch test
Hi, I wanted to re-create one of the original Udell-Fitch input file. Copying the input from the original tough manual, the attached is what I have. When I run it, I get an initial setting error.…
-
why the SAVE disk file is empty even i have no error message when i run the input file
hi all, i am learning tough 2 i found some training courses and tried to exercise i am interested in a Sample Problem 2DVZ: Infiltration Test in the Vadose Zone i tried to write the input file when…
-
Dual porosity flow crash
Hello, I'm trying to set up a EGS simulation where 120 °C water is injected into a 270 °C reservoir. The aim is to get the system up and running with TOUGHREACT but since those simulations keep on…
-
Incompressible flow
Dear all, I would like to consider the incompressible flow of the mixture CO2-brine in a heterogeneous reservoir. Are there any ways to fixe the density of brine and CO2 in TOUGH2?…
-
Sensitivity Analysis
Dear All, After running a CO2 injection model, I performed a sensitivity analysis to determine the sensitivity of my model with respect to some key input parameters (i.e.…
-
Water column above soil for infiltration processes
Dear Stefan, I investigate infiltration processes to look after the most effective one for a specific area. For that reason I would like not only to change the infiltration beginning and ending but…
-
Fracture porosity when using MINC in Tough2
Hi All, When we choose MINC in tough2, we need to input the porosity of fracture in the material data as in the following screen shot. What is the definition of the fracture porosity here?…
-
error message when using EXT.exe
Hello TOUGH users and specially Stefan, I need to export TOUGH2 results to Tecplot. I used EXT.exe but afte 6 timesteps this error message appears: forrt 1: severe <64> input conversion error,…
-
EOS7C tracer phase
Hi All, In EOS7C, what phase is the tracer in at injection? I have defined a Henry's constant, but presumably that takes effect after injection. Also, how can I see output for tracer in the liquid…
-
One question on outputting flow rate of aqueous VOC through COFT
Hello everyone, I have a question on outputting flow rate of aqueous VOC through COFT. I established a control plane in my model and want to simulate mass discharge through the control plane.…
-
about the output files of TOUGH-2: EOS9nT
For our research project I need to simulate the radioactive waste transport problems with EOS9nT. I am just at the beginning with learning EOS9nT, however, I have the problem about its output format.…
-
Relative permeability curves in tough2
Hello Every one I faced problem with the relative permeability curve while I working with tough2.1 to build a 3D reservor model for CO2 storage by using both the source code and also the petrasim…
-
XAIRL in volume element with no liquid phase
Hello TOUGH users! I am simulating a simple diffusion problem with EOS3. In my model, I have a volume element which is fully saturated with air and the rest of volume elements are fully saturated…
-
Data file Problem No.6 (*Case6_50kg_DP*) needed
Hello all. I am trying to run an EGS-CO2 model with TOUGH2 ECO2N. Is the example file Problem No.6 (*Case6_50kg_DP*) – GCS/GHE with a double-porosity reservoir in the manual available?…
-
injection using well on delivery
Hello, What is the correct way to use the well on delivery option for injection? Background: I'm using EOS7C and attempting to inject methane into my modeled domain at a depth of about 30 m below…
-
Implementing meteoric recharge into atmospheric boundary condition?
Hi all, Does anyone have a recommended method for specifying different rates of meteoric recharge to TOUGH2 models? Would specifying different air:water ratios in the atmospheric block work? Thanks,…
-
How to simulate bubble flow in non-Newtonian fluids (such as drilling mud)?
I am trying to create multiple simulation scenarios, one of them is to simulate discrete bubble flow through drilling much, which is also a non-Newtonian fluid.…
-
Recompiling EOS1 for using LUBAND
I have been trying to run the two water option in EOS1 to differentiate injection during a history match run but I'm not able to get a full run using the linear solvers.…
-
MINC and MIM
Hi All, I'm comparing MINC to mobile-immobile (MIM) models, most of which focus on transport (i.e., with the diffusion as the process connecting the two domains).…
-
Starting with TOUGH2v2
Hello everyone, I have TOUGH2 distributed by NEA. I recieved a DVD containing TOUGH2 source code, all of the EOS modules with '.F ' extension, and some input data for the sample problems.…
-
Why a simulation with "same" input file once runs and once crashes?
I made an input file which worked properly. I just added data block FOFT, and I recieved error by running that. I deleted data block FOFT but with the same input file which previously had worked…
-
use of MINC file in subsequent simulations
Dear all, I want to create a MINC file and use it in subsequent flow simulations. However, if I put the MESH and MINC file in the relevant folder, the simulation only uses the MESH file.…