-
ECO2M:run is not convergent
Dear TOUGH community users, I am using T2WELL/ECO2M to simulate the injection of CO2 into the aquifer, building a model of 0~-900 m (3D) and the aquifer is located in-750m~-800m.…
-
About the direction of xyz during mesh creation
Hi, When using meshmaker to make xyz type meshes, I had some confusion regarding the designation of these directions: (1) Regarding the DEG setting, is the angle negative clockwise or…
-
Temperature strange behavior
Dear TOUGH-community, I am simulating CO2 injection into a saline aquifer using T2Well/ECO2N - the model geometry is attached. Initially, the model is under hydrostatic equilibrium,…
-
Simulated CO2 injection into aquifers using T2WELL/ECO2M did not run successfully
Dear TOUGH community users, I am new to T2WELL/ECO2M and I am simulating CO2 injection into the aquifer, establishing a model of 0~-900m, the aquifer is located at -750~-800m,…
-
A problem about the direction of the anisotropic permeability
Hello everyone, I am using the EOS3 module to simulate the air and water flow in a hypothetical dome structure. I developed a 2-D radial model, and the PER in the ROCKS were set as 1e-12 (PER1),…
-
Error while running a T2LBM model
Does anyone know what is this error? forrtl: severe (157): Program Exception - access violation
-
run time error M6201:math
Hello everyone, I don't know where this error occurs and how to solve it, hopefully you can help me,thanks!
-
Empty SAVE file
Dear All, I have run the executable tough2 with the input is a DAT file (got it from Petrasim). When I run the simple model, it worked. But when I made a field model in Petrasim and got the DAT file,…
-
How to realize an air-injection well with constant bottom-hole pressure?
Dear all, I am using the EOS3 module to simulate the injection of air into a confined aquifer via a fully penetrating well. In order to prevent potential damage to the rock formation,…
-
The Example in TOUGH2's ECO2N:Radial Flow from a CO2 Injection Well
Dear all, I am using TOUGH2 ECO2N and I have confused about the example in Page 28 of the manual ECO2N: A TOUGH2 Fluid Property Module for Mixtures of Water,…
-
Inserting Permeability
Dear all, I am using Petrasim E0S5. I would like to know how to input different permeability and porosity for each grid block. My model is 3600 elements.…
-
EOS3-sink/source rates are piecewise constant, how to set up?
As mentioned in the title, I want to set the piecewise constant sink/source rate as shown in the attached figure, but I can't achieve the desired result after setting it many times in petrasim,…
-
Error For missing parameters,
My grid block size is 1 x 1 cm. The error said that I have a problem with specific element eventhough it is defined. I am not sure what is the issue. Could you please help me.
-
Heat generation in EOS3
Hello, I am a relatively new TOUGH2 user. I have developed a model for heat and fluid flow in a basin with a lake. I am attempting to have atmospheric boundary conditions are the top of the model…
-
Declining steam cap pressure
Dear TOUGH community, I am modeling a liquid-dominated geothermal reservoir underlying a steam cap. In the natural state I was able to match the cap pressure providing mass by means of several…
-
Defining Tortuosity
How to insert the tortuosity in Petrasim software?
-
Training
Is there any training for tough2 or tough3 for beginners?
-
The problem of using toughio to process input files
Hello Here is a test input file that can run normally(r2dl1). But when I use toughio to read and write, the output file(r2dl1_new) cannot be executed correctly. parameters = toughio.…
-
ECO2N: question about the VOLUME- AND MASS-BALANCES information in '.out ' file
Hi guys, As we can see in the 'out' file of eco2n, there is an information named VOLUME- AND MASS-BALANCES in the '.out' file. I don't know what HEAT stands for, is it internal energy or enthalpy?
-
Facing problem to match TOUGH output with excel and Python
Dear TOUGH community, Recently I am conducting 1-D stead-state radial heat conduction problem The result I got from PetraSim(TOUGH) could not match with the result from excel or python,…
-
ECO2N / ECO2M: handling of wettability in a dry zone
Hi folks, When exposing the initially brine-filled grid cells near injection point to CO2 injection, a dry zone is established. At a certain condition of flow and rock properties water saturation…
-
Error Message
Hi everyone, I have the following error message while running T2Well. Can anyone clarify what is the problem? At line 677 of file t2f.f (unit = 5, file = 'stdin') Fortran runtime error:…
-
How to import field reservoir properties data into reservoir model in TOUGH2?
Hi everyone, I have field data showing spatial temperature and salinity variation of a given reservoir. I would like to know if these data can be imported in a reservoir model in TOUGH2.…
-
Visualizing Results from T2Well using Paraview
Hi everyone, I am trying to visualize the results obtained from T2Well (OUTPUT file) using Paraview. I tried to use the following steps: 1. Install toughio in Anaconda prompt, 2.…
-
Errors when compiling TOUGH2 ECO2N
Hello Every one, When I compiled the TOUGH2 ECO2N in Microsoft Visual Studio, I met the problem as follow, could you please tell me how to solve it? I have added T2CG2.f, MA28.f, MESHM.f, T2f.…