-
Numerical Methods and Meshing Strategies
Hello, I am writing a research paper on different reservoir simulators in the market today. For the TOUGH simulators, I would like to get more information about the numerical methods that are used…
-
Problem 5: TCE Spill
Hi everyone, I use TMVOC to reproduce the problem n°5 in the T2VOC User's Guide with an additionnal VOC, which is PCE (tetrachloroethylene). I am a little bit stuck as I try to run the first part.…
-
Analytical solution for TOUGH2-ECO2N
Hello I am currently using TOUGH2-ECO2N. I would like to compare and check my numerical results with an analytical solution. I am wondering if "Theis solution" is applicable to simulate the CO2…
-
Dual porosity flow crash
Hello, I'm trying to set up a EGS simulation where 120 °C water is injected into a 270 °C reservoir. The aim is to get the system up and running with TOUGHREACT but since those simulations keep on…
-
Scientific format of numbers in TOUGH2 input file
Hi. I just experienced some strange behavior when trying to run 1D gravity equilibrium for ECO2N module with TOUGH2-MP for test case 4 (rtp7). I used the following ROCKS block in the input file…
-
simulating diffusion process in long time (near equilibrium) with TOUGH2
Hi! I am trying to simulate a simple diffusion poblem with TOUGH2. I am using EOS3, I can't get any results for long term (near equilibrium time which is in my problem around 80 days).…
-
Signal SIGSEGV: Segmentation fault
Dear all, I just encountered following error while executing a TOUGH-ECO2M sample problem: Program received signal SIGSEGV: Segmentation fault - invalid memory reference.…
-
Error Message - out of range in SATB
My simulation of injecting co2 into a homogeneous reservoir using eco2n stops with the error message: +++++++++ REDUCE TIME STEP AT ( 50, 1) ++++++++++++++++ NEW DELT = 0.…
-
Incompressible flow
Dear all, I would like to consider the incompressible flow of the mixture CO2-brine in a heterogeneous reservoir. Are there any ways to fixe the density of brine and CO2 in TOUGH2?…
-
Initialization problem for ECO2N Problem No. 4 (rtp7)
Hello everyone, I'm new to TOUGH2.In running the fourth example of ECO2N, I don't understand how to set the initial conditions. 1. The manual mentions only involving boundary grid cells with…
-
Unable to execute code due to plugin not found?
Hello everyone, how can I solve this problem? I tried downloading the corresponding plugin but still couldn't solve the problem.
-
Aspadol 100mg – HealthNaturo
Aspadol 100mg is a brand of Tapentadol. It is a pain medicine that treats acute as well as chronic body pain. People who are suffering from arthritis, neuropathic pain, post-surgery pain,…
-
Artvigil vs Waklert
Artvigil and Waklert are both products of Armodafinil that belong to the drug class Nootropic. These are prescribed to treat extreme sleepiness disorders due to narcolepsy, sleep apnea,…
-
Modafinil for excessive daytime sleepiness
Modafinil is a Nootropic that promotes wakefulness and helps treat excessive daytime sleepiness. It is an effective option that works within 30 minutes of intake and stays active for about 15 hours.…
-
The pore pressure decreased near the non-reservoir wellbore during the CO2 injection process
Dear TOUGH community users, When I used T2WELL/ECO2N to simulate carbon dioxide non-isothermal injection, I found that when using cryogenic supercritical CO2 injection,…
-
Anabrez For Breast Cancer Treatment - Genericcures
Anabrez appears as an essential partner in the treatment of breast cancer, designed specifically for postmenopausal women with hormone receptor-positive tumors.…
-
low injection rate can induce the EOS CANNOT FIND PARAMETERS?
Hi,everyone I want to simulate the dissolution and precipitation induced by meteoric water injection (toughreact332_EOS1). I set injection rate 9.5129E-02 kg/s during 2Ma,…
-
Temperature strange behavior
Dear TOUGH-community, I am simulating CO2 injection into a saline aquifer using T2Well/ECO2N - the model geometry is attached. Initially, the model is under hydrostatic equilibrium,…
-
Error while running a T2LBM model
Does anyone know what is this error? forrtl: severe (157): Program Exception - access violation
-
run time error M6201:math
Hello everyone, I don't know where this error occurs and how to solve it, hopefully you can help me,thanks!
-
How to import field reservoir properties data into reservoir model in TOUGH2?
Hi everyone, I have field data showing spatial temperature and salinity variation of a given reservoir. I would like to know if these data can be imported in a reservoir model in TOUGH2.…
-
how could FLAC3D simulate the deterioration of soil when coupling with TOUGH
I am read many essay about FLAC3D+TOUGH, including FLAC3D+TOUGH2 and FLAC3D+TOUGH+HYDRATE, and i have completed the couple with FLAC3D AND TOUGH+HYDRATE,…
-
T2well output files
Hello T2well users; I have just started using the code. I run a case with only a well model (reservoir represented solely by the last grid block at the bottom).…
-
CO2TAB file in ECO2N
Hello to everyone ! ***I apologize for copying the post, but I have published the previous one in the wrong section.*** I would like to model CO2 injection into high temperature and high pressure…
-
Beginner
Hello everyone, I just got Petrasim+Tough2 licence from work but I have no idea where to start and how to start. I have noone around to ask and no experience with other simulators either.…